You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Hub Motor Remote Control by bf01 on Tue, 2017-11-14 16:04 |
3 |
by frank Wed, 2017-12-06 23:41 |
General discussion | |
bugreport. Scale useless by Roger Wolff on Wed, 2017-11-29 12:24 |
1 |
by Svenska Svenson Mon, 2017-12-04 07:56 |
VESC Tool | |
RPM measurement. by Roger Wolff on Wed, 2017-11-29 16:48 |
2 |
by Roger Wolff Fri, 2017-12-01 06:25 |
General discussion | |
Servo Motor position control by wdaehn on Wed, 2017-11-29 21:45 |
by wdaehn Wed, 2017-11-29 21:45 |
Feature Requests | ||
Initial Setup wizard fails, HW 4.10 by wdaehn on Tue, 2017-09-12 18:47 |
7 |
by wdaehn Wed, 2017-11-29 14:21 |
VESC Tool | |
Using vesc for Position and driving my BB8 Robot by Quicksilverstar on Wed, 2017-11-15 19:25 |
4 |
by Quicksilverstar Sat, 2017-11-25 16:11 |
General discussion | |
Upgraded from 2.18 to 3.33 - Lost Telemetry by ervinelin on Thu, 2017-11-23 09:09 |
1 |
by Pedrodemio Thu, 2017-11-23 17:03 |
VESC Firmware | |
Can't ajust braking torgue with Plettenberg Predator 30/8 by VescBuilder on Sun, 2017-11-12 16:13 |
6 |
by benjamin Thu, 2017-11-23 09:38 |
Third Party Hardware | |
Need advice : repair , vesc 4.12, vesc 6.4 or wait ? by frameto on Mon, 2017-11-20 21:57 |
2 |
by frameto Wed, 2017-11-22 22:01 |
VESC Original Hardware | |
Commutation sync by TechAUmNu on Mon, 2017-11-20 17:40 |
1 |
by benjamin Wed, 2017-11-22 11:12 |
Feature Requests | |
about reference hardware by qdxiatao on Mon, 2017-09-25 08:32 |
10 |
by lizardmech Tue, 2017-11-21 19:40 |
General discussion | |
Charge wires by Phill Dixon on Tue, 2017-10-24 14:24 |
4 |
by linsus Tue, 2017-11-21 14:39 |
General discussion | |
Battery power by Phill Dixon on Tue, 2017-11-14 20:14 |
4 |
by slapshot136 Tue, 2017-11-21 05:01 |
General discussion | |
Question about improvement og VESC 6.4 by StreetSkater on Sat, 2017-11-18 08:03 |
1 |
by Roger Wolff Sat, 2017-11-18 12:01 |
General discussion | |
At standstill a 30A limit? by Roger Wolff on Fri, 2017-11-17 09:37 |
2 |
by Roger Wolff Sat, 2017-11-18 11:58 |
General discussion | |
PPM Voltage Output? by josh on Sun, 2017-06-18 21:39 |
2 |
by wouavier Thu, 2017-11-16 10:55 |
VESC6 Beta | |
temp motor by emmaanuel on Wed, 2017-09-13 01:27 |
12 |
by Roger Wolff Wed, 2017-11-08 16:23 |
VESC Firmware | |
Switch between different modes via remote by Cledus on Sun, 2017-10-22 13:56 |
2 |
by MatwoSvK Tue, 2017-11-07 22:32 |
VESC Tool | |
Dual Vesc6 setup: Vesc with nrf no blue light by Paul15578 on Sat, 2017-11-04 04:00 |
2 |
by Paul15578 Mon, 2017-11-06 13:56 |
VESC Original Hardware | |
ws8212 and VESC firmware by dannlh on Fri, 2017-11-03 04:17 |
2 |
by dannlh Sat, 2017-11-04 18:47 |
General discussion |