You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Sticky:
VESC 75/300 R2 with R1 Firmware by frank » Thu, 2019-11-28 09:39 |
1 |
by Henque19 Sat, 2021-04-24 22:48 |
|
|
firmware by Muhammad Rifan » Tue, 2025-11-04 08:17 |
0 |
by Muhammad Rifan Tue, 2025-11-04 08:17 |
|
|
CAN sends error frame by dgarciasoto » Wed, 2022-04-27 07:11 |
2 |
by fingerprintdax Thu, 2025-10-02 00:46 |
|
|
FSESC 75100 Pro V2 W/ ALUMINUM by drstein99 » Tue, 2025-08-26 23:02 |
1 |
by Brett.W Mon, 2025-09-01 14:44 |
|
|
Lispbm Scripting by Sanderehv87 » Wed, 2025-08-27 00:49 |
0 |
by Sanderehv87 Wed, 2025-08-27 00:49 |
|
|
Change the direction of motor when using PPM and "Current no reverse with brake"? by Kokonenen » Mon, 2023-04-24 13:41 |
1 |
by tokerodev Thu, 2025-08-21 11:10 |
|
|
Unity FW updating bricked my 4.12 HW by yuvikal » Thu, 2019-12-12 22:16 |
5 |
by tokerodev Thu, 2025-08-21 11:02 |
|
|
Dual motor control on VESC6 / 6.00.58 by jediengineer » Mon, 2022-10-10 19:21 |
5 |
by RSR Sat, 2025-08-09 18:23 |
|
|
firmware w/ no hw limits by dewcantoo » Sat, 2025-07-19 21:10 |
0 |
by dewcantoo Sat, 2025-07-19 21:10 |
|
|
bootloader and firmware update for vesc 4.12 by enjoae » Thu, 2025-05-22 19:17 |
2 |
by tobydraper Sun, 2025-06-15 22:22 |
|
|
Innotrace X1 motor controller for Bafang m620 UART with VESC firmware by TPEHAK » Tue, 2025-06-10 22:00 |
0 |
by TPEHAK Tue, 2025-06-10 22:03 |
|
|
Help needed compiling vesc express for esp32 mini D1 by mrendu43 » Sun, 2023-02-05 18:00 |
3 |
by mvturnho Wed, 2025-05-14 08:46 |
|
|
VESC 6 plus working but no servo response by saspragkathos » Mon, 2020-06-29 17:28 |
1 |
by Shreeram2311 Tue, 2025-05-06 02:44 |
|
|
vesc disconnected during detection by TonyYuan » Mon, 2023-06-26 09:17 |
2 |
by powerpedalph Thu, 2025-04-24 07:51 |
|
|
Focbox Unity by Remedii » Sat, 2024-06-08 04:23 |
3 |
by Unspoken Fri, 2025-04-18 06:26 |
|
|
firmware V6.06 vs VESC tool V6.05 by shuang » Thu, 2024-12-05 06:49 |
3 |
by Polyloop Mon, 2025-03-31 17:34 |
|
|
Flipsky 75100 not running after firmware update by defazioaa » Sat, 2025-03-29 01:33 |
0 |
by defazioaa Sat, 2025-03-29 01:33 |
|
|
Uploaded Firmware, Not Updated by kneave » Sat, 2018-08-18 21:02 |
3 |
by Bernardo Moreira Wed, 2025-03-26 12:32 |
|
|
How to edit parametrs over limit? by vescbeginer » Sun, 2025-02-02 12:54 |
0 |
by vescbeginer Sun, 2025-02-02 12:54 |
|
|
What is the recommended way to implement a new encoder in the VESC firmware? by toma » Mon, 2019-11-04 00:19 |
3 |
by James Donker Mon, 2025-01-27 18:53 |
|
|
VESC 4.7 old firmware update issue by Lars_Dierickx » Sun, 2023-03-19 15:39 |
5 |
by Racenut286 Sat, 2025-01-11 19:59 |
|
|
vx2 remote no longer working for updated 75100 v2 firmware by Noa135 » Mon, 2024-12-23 00:47 |
3 |
by trhaitsuka Fri, 2024-12-27 18:06 |
|
|
Vesc 6.5 - Issue with Canbus Status Command by Angelo99 » Thu, 2024-12-19 16:54 |
0 |
by Angelo99 Thu, 2024-12-19 16:54 |
|
|
Help needed VESC - Update missed? by JUST1975 » Tue, 2024-11-26 11:43 |
1 |
by JUST1975 Tue, 2024-11-26 11:53 |
|
|
position hold below specific duty cycle by lacondro » Wed, 2022-04-27 04:41 |
2 |
by cjmssmd Thu, 2024-11-21 21:29 |
Log in to post new content in the forum.
