You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Lack of throttle control / too fast by mgisch on Mon, 2019-04-01 05:57 |
6 |
by mgisch Wed, 2019-04-03 09:53 |
Third Party Hardware | |
|
4 BLDC for 1 VESC by mac_cros on Wed, 2019-03-20 16:45 |
8 |
by tul00985 Wed, 2019-04-03 08:32 |
Third Party Hardware | |
|
Current control and duty cycle issues. by ESCam on Tue, 2019-04-02 22:55 |
by ESCam Tue, 2019-04-02 22:55 |
General discussion | ||
|
Phase A not working and GVDD_OV/GVDD_UV DRV faults by chocol4te on Mon, 2019-04-01 15:32 |
by chocol4te Mon, 2019-04-01 15:32 |
Third Party Hardware | ||
|
Braking in speed PID controlled mode by vadimz on Sat, 2018-09-15 14:19 |
9 |
by zybyxutese Mon, 2019-04-01 13:35 |
General discussion | |
|
Vesc tool mobile for raspbian by Idoff on Sat, 2019-03-30 19:24 |
by Idoff Sat, 2019-03-30 19:24 |
VESC Tool | ||
|
no speed feedback in DC mode by Jessica on Mon, 2018-11-19 11:17 |
6 |
by abrac Sat, 2019-03-30 19:11 |
General discussion | |
|
Video Live Streams of a dual drive based on stm32f429 by mkschreder on Sat, 2019-03-30 16:25 |
by mkschreder Sat, 2019-03-30 16:28 |
Third Party Hardware | ||
|
VESC6 runs at 100% throttle, but then current sense is broken by nickw1881 on Mon, 2018-09-24 06:41 |
2 |
by moto_guy Thu, 2019-03-28 06:40 |
VESC Firmware | |
|
Setup parameters for battery in VESC Tool by Ulrich on Tue, 2019-02-26 11:47 |
3 |
by Photolad61 Wed, 2019-03-27 17:26 |
VESC Tool | |
|
STM32F407 by john on Wed, 2019-03-27 13:40 |
by john Wed, 2019-03-27 13:40 |
General discussion | ||
|
Vesc-Tool mobile on Play Store. by frank on Fri, 2019-02-15 19:54 |
11 |
by Boesila Mon, 2019-03-25 20:28 |
VESC Tool | |
|
Custom App: Motor dont stop by CTSchorsch on Fri, 2019-03-22 13:43 |
by CTSchorsch Fri, 2019-03-22 13:43 |
VESC Firmware | ||
|
Enhance position and rpm control interface / protocol by brushlessjoe on Wed, 2019-03-20 21:54 |
by brushlessjoe Wed, 2019-03-20 21:54 |
Feature Requests | ||
|
E vehicle setup by jordanlow on Wed, 2019-03-20 10:33 |
4 |
by jordanlow Wed, 2019-03-20 16:18 |
General discussion | |
|
BEMF plot not working with VESC6 by ESCam on Tue, 2019-03-12 21:29 |
2 |
by ESCam Tue, 2019-03-19 18:03 |
VESC Tool | |
|
Master Slave Controller for Motor by Blemot on Tue, 2019-03-19 09:46 |
by Blemot Tue, 2019-03-19 09:46 |
General discussion | ||
|
Motion commands for controlling CNCs by andresv on Fri, 2017-09-08 10:35 |
2 |
by brushlessjoe Sun, 2019-03-17 21:29 |
Feature Requests | |
|
Driving Issues Due To Reversed Current Amplification by F4metz on Mon, 2018-12-17 16:45 |
1 |
by moto_guy Sun, 2019-03-17 02:39 |
Third Party Hardware | |
|
Connection over USB failed by sangious on Sun, 2019-03-17 01:20 |
by sangious Sun, 2019-03-17 01:20 |
VESC Tool |
Pages
