You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Sticky:
Motor Values in VESC-Tool 2019 by frank » Wed, 2019-02-27 09:40 |
19 |
by Onarb Kabr Wed, 2025-01-15 13:28 |
|
|
Sticky:
FOC wizard confusion by Stupidspencer » Mon, 2019-07-08 04:18 |
4 |
by lurch Sun, 2021-10-24 14:46 |
|
|
Sticky:
Step by Step Setup by frank » Wed, 2017-10-04 17:15 |
8 |
by mc Tue, 2018-02-20 11:12 |
|
|
Constant Serial port errors by SteveBrantley » Tue, 2025-01-21 23:13 |
0 |
by SteveBrantley Tue, 2025-01-21 23:13 |
|
|
Urgent Help Connecting TS5700N8501-like Magnetic Encoder by jumana » Tue, 2025-01-14 19:37 |
0 |
by jumana Tue, 2025-01-14 19:37 |
|
|
NVIDIA Jetson AGX Outputting PWM to Flipsky VESC Issue by colemalinchock » Tue, 2025-01-14 00:40 |
0 |
by colemalinchock Tue, 2025-01-14 00:40 |
|
|
Custom GUI by FatsoBatso » Thu, 2021-02-25 16:10 |
1 |
by onid Mon, 2025-01-13 22:00 |
|
|
6MK6 Can Statusmessages by maxmertins » Fri, 2024-09-20 11:36 |
1 |
by Angelo99 Tue, 2025-01-07 10:18 |
|
|
IOS - VESCTOOL Run successfully ? by Bear Chris » Mon, 2025-01-06 08:54 |
2 |
by Bear Chris Mon, 2025-01-06 15:06 |
|
|
Odys Alpha X3 Pro Settings by flashice » Mon, 2025-01-06 14:28 |
0 |
by flashice Mon, 2025-01-06 14:34 |
|
|
lispBM command "gpio-hold" by Jamesavery22 » Sat, 2025-01-04 20:46 |
0 |
by Jamesavery22 Sat, 2025-01-04 20:46 |
|
|
Unable to Make Changes in VESC Tool – field weakening Options Missing by asaf1462 » Tue, 2024-12-17 16:27 |
1 |
by Jamesavery22 Sat, 2025-01-04 19:32 |
|
|
Lisp scripting questions/suggestions/remarks by Gatze » Sun, 2022-04-24 12:13 |
1 |
by Jamesavery22 Sat, 2025-01-04 04:58 |
|
|
FOC is unstable with large Outrunner and had a hardware failure. by SteveBrantley » Tue, 2024-12-31 16:23 |
1 |
by SteveBrantley Wed, 2025-01-01 19:55 |
|
|
Issues with Brakes, M5 Display, and Speed on VESC 75100 by asaf1462 » Sun, 2024-12-08 15:50 |
0 |
by asaf1462 Sun, 2024-12-08 15:50 |
|
|
VESC Tool Device UI not shown on Raspberry Pi/Linux by Sebastiaan Koning » Mon, 2024-12-02 13:19 |
0 |
by Sebastiaan Koning Mon, 2024-12-02 13:19 |
|
|
Help "ERASE" Lisp Script that crashes VESC TOOL (terminal command?) by ebikebuilder_yt » Thu, 2024-08-01 20:16 |
2 |
by onid Sat, 2024-11-23 21:59 |
|
|
Download latest VESC Tool version by consti » Wed, 2022-06-15 17:24 |
5 |
by Tom@ Tue, 2024-11-19 16:45 |
|
|
Vesc tool not working on Windows 11 Surface Go tablet by Kamil368 » Tue, 2024-11-19 00:09 |
1 |
by Kamil368 Tue, 2024-11-19 00:35 |
|
|
[Solved] VESC Tool "could not deserialize motor configuration" with custom firmware by bsobeloffgittes » Fri, 2024-05-03 20:30 |
2 |
by rafeh1 Wed, 2024-11-06 09:14 |
|
|
How to read COMM_ROTOR_POSITION through uart by Graham Bowen-Davies » Wed, 2021-04-28 23:59 |
4 |
by mansi712 Tue, 2024-11-05 17:57 |
|
|
Rough Stutter when taking off (48V 750w 75100 Pro v2) by ahagie » Mon, 2024-11-04 01:21 |
0 |
by ahagie Mon, 2024-11-04 01:21 |
|
|
How can we log all the real time data like motor current, battery current,etc to analyze them later? by vimi94 » Thu, 2019-05-02 09:57 |
27 |
by Stock88 Sun, 2024-11-03 04:02 |
|
|
Can't spin both motors over CAN-bus by Kokonenen » Wed, 2023-04-19 11:19 |
4 |
by mansi712 Wed, 2024-10-30 13:40 |
|
|
"CAN bus support is not enabled in this build of VESC Tool" by hdfghdfgh » Wed, 2023-04-26 16:13 |
2 |
by mansi712 Mon, 2024-10-28 12:19 |
Log in to post new content in the forum.
