You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Flipsky 72150 outboard cannot connect via USB by EddieEagle1970 on Sat, 2026-02-21 16:56 |
by EddieEagle1970 Sat, 2026-02-21 16:56 |
General discussion | ||
|
unable to read my firmware and connect by henryo on Wed, 2025-11-26 02:16 |
1 |
by Ampit Thu, 2026-02-19 08:10 |
VESC Firmware | |
|
best way to control motor over UART by harold on Fri, 2026-02-13 15:31 |
by harold Mon, 2026-02-16 16:06 |
Projects incorporating VESC technology | ||
|
No Single Direction ADC in FW v6.06??? by rcalicea on Fri, 2026-02-13 09:15 |
by rcalicea Fri, 2026-02-13 09:23 |
VESC Tool | ||
|
VESC 4.7 old firmware update issue by Lars_Dierickx on Sun, 2023-03-19 15:39 |
6 |
by Bonar Wed, 2026-02-11 15:34 |
VESC Firmware | |
|
Set current - is it input or phase current? by aegidius on Sun, 2026-02-08 05:58 |
by aegidius Sun, 2026-02-08 05:58 |
General discussion | ||
|
Motor detection and calibration using CAN by charan on Tue, 2026-02-03 14:48 |
by charan Tue, 2026-02-03 14:48 |
General discussion | ||
|
VESC tool for windows by djevIen on Mon, 2019-06-17 08:02 |
3 |
by domkavesc Tue, 2026-02-03 00:22 |
VESC Tool | |
|
UI problem by Zeos on Fri, 2026-01-30 11:29 |
by Zeos Fri, 2026-01-30 11:29 |
VESC Tool | ||
|
Blue and Purple Light Flashing on Vesc 6mk VI controller by electro_man on Wed, 2026-01-28 23:56 |
by electro_man Wed, 2026-01-28 23:56 |
VESC Original Hardware | ||
|
Low-Speed Hall Interpolation Performance Issues by cpaterson on Tue, 2026-01-27 03:42 |
by cpaterson Tue, 2026-01-27 03:42 |
VESC Firmware | ||
|
High res ABI encoder on Vesc not working by JH on Sun, 2026-01-25 01:23 |
by JH Sun, 2026-01-25 01:23 |
General discussion | ||
|
Measured stator resistance not consistent by LoicLL on Wed, 2026-01-21 18:15 |
1 |
by LoicLL Fri, 2026-01-23 17:32 |
VESC Firmware | |
|
Question about duty cycle control Vs current control mode by hazzahodgson on Wed, 2026-01-21 08:34 |
by hazzahodgson Wed, 2026-01-21 08:34 |
General discussion | ||
|
ESP-NOW Remote control by brightlightbeam on Sun, 2026-01-18 12:00 |
1 |
by A-damW Wed, 2026-01-21 04:28 |
General discussion | |
|
VESC Tool RPM not the actual in real life by Poh Boon pin on Sun, 2021-07-11 16:00 |
3 |
by Klamauk Wed, 2026-01-14 22:32 |
VESC Tool | |
|
VESC 100/250MK issues with output power by martin321 on Tue, 2026-01-13 09:52 |
1 |
by electricfox Tue, 2026-01-13 19:21 |
VESC Original Hardware | |
|
Vesc Pronto Hall Sensors not detecting by lcappellano on Sun, 2026-01-11 19:27 |
1 |
by electricfox Mon, 2026-01-12 11:40 |
VESC Original Hardware | |
|
"CAN bus support is not enabled in this build of VESC Tool" by hdfghdfgh on Wed, 2023-04-26 16:13 |
5 |
by Nshoup Sat, 2026-01-10 01:30 |
VESC Tool | |
|
Flipsky 75100 to drive E-Bike BLDC motor in torque mode w/back by vescUN on Mon, 2026-01-05 10:13 |
by vescUN Mon, 2026-01-05 15:00 |
Third Party Hardware |
Pages
