You are here

VESC Original Hardware

Topic / Topic starter Replies Last postsort ascending
Normal topic VESC 6 Plus reseting settings and firmware
by granstubbe » Fri, 2020-01-10 18:31
1
by frank
Mon, 2020-01-27 21:24
Hot topic VESC75/300
by frank » Fri, 2018-11-23 10:04
30
by Henque19
Sun, 2020-01-26 23:30
Normal topic Choosing Motor Encoder for VESC
by VRdublove » Fri, 2020-01-24 18:51
0
by VRdublove
Fri, 2020-01-24 21:44
Normal topic Controlling multiple VESC over SPI
by ttufuor » Mon, 2019-11-18 04:37
2
by Danny Bokma
Fri, 2020-01-24 18:29
Normal topic BLDC control in FOC mode
by da_rul0r » Fri, 2019-08-16 15:32
1
by Ulrich
Mon, 2020-01-20 19:43
Normal topic VESC 75/300 with sin/cos encoder
by sajjen » Tue, 2019-11-12 16:16
4
by marcos_
Sun, 2020-01-19 22:48
Normal topic VESC 100/250
by Oliver » Mon, 2020-01-13 20:23
2
by marc426
Sat, 2020-01-18 22:32
Normal topic Power switch on VESCT6+ (MK3)
by henry10210 » Thu, 2019-12-26 00:47
7
by adamchicago
Thu, 2020-01-16 19:52
Normal topic Weird behaviour on overcurrent : have to reflash then FOC doesn't work
by marc426 » Tue, 2020-01-07 23:58
9
by marc426
Wed, 2020-01-15 16:35
Normal topic Hall sensor not working
by Stupidspencer » Sat, 2019-12-28 20:29
1
by Stupidspencer
Mon, 2020-01-13 00:37
Normal topic VESC design specification, manual
by velolac » Thu, 2020-01-02 15:54
1
by velolac
Sat, 2020-01-11 00:05
Normal topic builtin ble on vesc 75_300
by alexefoil » Wed, 2019-07-03 02:35
5
by frank
Thu, 2019-12-05 11:29
Normal topic VESC 6 Schematic Question
by mendez » Tue, 2019-02-12 07:11
8
by frank
Thu, 2019-12-05 11:28
Normal topic 75/300 NRF Pairing
by eptv » Sat, 2019-10-12 14:47
3
by frank
Thu, 2019-12-05 11:22
Normal topic Can't program bricked Vesc 6 over SWD
by Rc 44 » Thu, 2019-06-20 02:16
5
by Rc 44
Wed, 2019-11-06 01:44
Normal topic Vesc 6 and encoder connections
by eptv » Thu, 2019-10-31 15:46
1
by eptv
Mon, 2019-11-04 08:03
Normal topic VESC 75/300 liquid cooling
by niekvanprooijen » Mon, 2019-09-09 19:15
4
by tedchaplin
Thu, 2019-10-31 02:27
Normal topic Driving two motors with 75/300
by cmarc » Wed, 2019-10-16 17:32
1
by benjamin
Fri, 2019-10-18 10:37
Normal topic VESC 4.12 Duty is always 110%. Possible short?
by tahirali1 » Sun, 2019-10-13 14:22
0
by tahirali1
Sun, 2019-10-13 14:22
Normal topic fault_code_high_offset_current_sensor_1
by Enak » Thu, 2019-10-10 02:48
2
by Enak
Fri, 2019-10-11 01:24
Normal topic VESC 75/300 current noise / losing sync?
by ezonca » Thu, 2019-10-03 23:06
2
by benjamin
Thu, 2019-10-10 07:56
Normal topic VESC 4.12 - Data loss on power off
by da_rul0r » Wed, 2019-08-14 16:43
2
by da_rul0r
Thu, 2019-08-15 08:33
Normal topic Hooking up two or more motor drivers  to the same MCU 
by darkclaude » Thu, 2019-06-20 10:02
2
by skyline1970
Wed, 2019-07-31 13:53
Normal topic VESC Hardware
by eschroff » Thu, 2019-07-25 02:38
1
by skyline1970
Wed, 2019-07-31 13:35
Normal topic Programming Vesc 4.12 motor spin only in detection mode
by DanieleRA » Sun, 2019-07-28 16:29
0
by DanieleRA
Sun, 2019-07-28 16:29
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - VESC Original Hardware