You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Issues using vesc for Gimbal Motor iPower GM5208-24 by marcnyffenegger » Fri, 2026-05-15 15:18 |
0 |
by marcnyffenegger Fri, 2026-05-15 15:18 |
|
|
How to read MotorRPM from UART to Arduino by azobe » Thu, 2018-03-08 14:42 |
4 |
by Muhammad Usman Fri, 2026-05-15 09:14 |
|
|
VESC App - Android - "App not installed" error by KColborne » Mon, 2023-03-27 22:11 |
2 |
by NOAI Wed, 2026-05-13 08:03 |
|
|
SPINTEND UBOX 100v100a x2 or Flipsky 75100 100v100a x2 by DuckyTheDuck » Mon, 2022-09-26 12:07 |
4 |
by primarc1982 Sat, 2026-05-09 07:16 |
|
|
Duty Cycle with brake switch and PAS by m620 » Tue, 2026-04-28 03:50 |
0 |
by m620 Tue, 2026-04-28 03:50 |
|
|
Flipsky 65220 by mcfoilvesc » Sun, 2026-04-26 20:15 |
0 |
by mcfoilvesc Sun, 2026-04-26 20:15 |
|
|
Forward/brake/reverse mode? by RDN2003 » Thu, 2019-10-03 02:13 |
9 |
by Toymanfrank Sun, 2026-04-26 03:49 |
|
|
Voltage Calibration by Frantin » Mon, 2026-04-20 21:40 |
0 |
by Frantin Mon, 2026-04-20 21:40 |
|
|
Field weakening in reverse? by Toymanfrank » Wed, 2026-04-15 04:40 |
0 |
by Toymanfrank Wed, 2026-04-15 04:40 |
|
|
Quiescent Current with FOC and PID by twald » Mon, 2026-03-23 03:37 |
1 |
by twald Mon, 2026-03-23 14:05 |
|
|
ABI maximum speed by liran vigdor » Fri, 2026-03-20 17:00 |
1 |
by liran vigdor Fri, 2026-03-20 17:01 |
|
|
Cruise Control on VESC 75200 by djambobuksne » Mon, 2026-03-09 19:41 |
1 |
by CRTZ Wed, 2026-03-18 14:24 |
|
|
Dultron X2 UP by timgunn5555 » Wed, 2026-03-18 02:34 |
0 |
by timgunn5555 Wed, 2026-03-18 02:34 |
|
|
[SOLVED] PWM speed control at low RPM by comes04 » Sun, 2023-04-16 13:30 |
2 |
by andrej.pangerci... Mon, 2026-03-16 18:03 |
|
|
mini fsesc4.20 help by bravo29 » Mon, 2026-03-16 17:14 |
0 |
by bravo29 Mon, 2026-03-16 17:14 |
|
|
The controller is not responding by TheJuan901 » Sat, 2026-03-14 02:03 |
0 |
by TheJuan901 Sat, 2026-03-14 02:03 |
|
|
MXUS 3K 5T Stuttering, Desync, Cogging sounds FSESC 75200 Pro V2 72V by djambobuksne » Mon, 2026-02-23 20:05 |
4 |
by djambobuksne Mon, 2026-03-09 19:38 |
|
|
MakerX-FOC DV6s PWM for 2 BLDC Motors by paulsimpsonii » Tue, 2026-03-03 18:08 |
0 |
by paulsimpsonii Tue, 2026-03-03 18:08 |
|
|
Flipsky 75100 pro v2 ADC throttle stopped responding by JozoBozo » Tue, 2026-02-24 17:33 |
2 |
by JozoBozo Sun, 2026-03-01 13:40 |
|
|
Flipsky 72150 outboard cannot connect via USB by EddieEagle1970 » Sat, 2026-02-21 16:56 |
2 |
by mariuszdymon Sat, 2026-02-28 23:37 |
|
|
KERS system with a VESC 100/250 MKIII by Simone Succi » Thu, 2026-02-26 08:28 |
0 |
by Simone Succi Thu, 2026-02-26 16:20 |
|
|
Set current - is it input or phase current? by aegidius » Sun, 2026-02-08 05:58 |
0 |
by aegidius Sun, 2026-02-08 05:58 |
|
|
Motor detection and calibration using CAN by charan » Tue, 2026-02-03 14:48 |
0 |
by charan Tue, 2026-02-03 14:48 |
|
|
High res ABI encoder on Vesc not working by JH » Sun, 2026-01-25 01:23 |
0 |
by JH Sun, 2026-01-25 01:23 |
|
|
Question about duty cycle control Vs current control mode by hazzahodgson » Wed, 2026-01-21 08:34 |
0 |
by hazzahodgson Wed, 2026-01-21 08:34 |
Log in to post new content in the forum.
