You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
VESC 4.12 Duty is always 110%. Possible short? by tahirali1 on Sun, 2019-10-13 14:22 |
by tahirali1 Sun, 2019-10-13 14:22 |
VESC Original Hardware | ||
|
USB connection problem by Ironman223 on Sat, 2019-10-12 13:53 |
by Ironman223 Sat, 2019-10-12 13:53 |
VESC Firmware | ||
|
fault_code_high_offset_current_sensor_1 by Enak on Thu, 2019-10-10 02:48 |
2 |
by Enak Fri, 2019-10-11 01:24 |
VESC Original Hardware | |
|
Wand Cruise Control, and speed control only working on Master VESC by MaddiQ on Mon, 2019-09-16 20:46 |
15 |
by hans_maier Fri, 2019-10-11 00:22 |
General discussion | |
|
BLDC Motor Power limitation by tecnico.solarboat on Tue, 2019-10-01 23:42 |
4 |
by tecnico.solarboat Thu, 2019-10-10 15:13 |
General discussion | |
|
Limiting switching frequency of the SPWM for big IGBT´s by javivi on Wed, 2019-10-09 13:32 |
2 |
by javivi Thu, 2019-10-10 09:41 |
VESC Firmware | |
|
VESC 75/300 current noise / losing sync? by ezonca on Thu, 2019-10-03 23:06 |
2 |
by benjamin Thu, 2019-10-10 07:56 |
VESC Original Hardware | |
|
Second uart? by Kubbur on Mon, 2019-09-16 19:32 |
2 |
by benjamin Thu, 2019-10-10 07:34 |
General discussion | |
|
Does a wireless passive on/off ignition switch that holds its state exist? Need help for my custom electric scooter! by 010203040506070809 on Mon, 2019-09-30 23:59 |
1 |
by Enak Thu, 2019-10-10 03:21 |
General discussion | |
|
ADC and arrow input dont work by stefann on Wed, 2019-10-09 18:51 |
by stefann Wed, 2019-10-09 20:04 |
VESC Tool | ||
|
Hall sensors signals tolerance by Pimousse on Tue, 2019-09-17 13:55 |
4 |
by e-biker Wed, 2019-10-09 12:40 |
General discussion | |
|
s for second S for siemens by maxxximatoze on Mon, 2019-10-07 12:22 |
by maxxximatoze Mon, 2019-10-07 12:22 |
VESC Tool | ||
|
VESC Tool returns bad ERPM value by karololo on Thu, 2019-10-03 10:12 |
1 |
by TechAUmNu Fri, 2019-10-04 15:05 |
VESC Tool | |
|
IMU support and alternate IMU ICs (Bosch bmi160?) by shaman on Fri, 2019-09-20 15:04 |
2 |
by shaman Thu, 2019-10-03 19:06 |
General discussion | |
|
Measure resistance with IGBTs by mtzm on Wed, 2018-04-04 14:46 |
4 |
by jaredreese Thu, 2019-10-03 11:41 |
VESC Firmware | |
|
What Software to plan custom VESC by Plermpel on Mon, 2019-09-30 22:16 |
1 |
by frank Tue, 2019-10-01 10:29 |
General discussion | |
|
VESC Design - Review and Bringup - 150V - 20A by ripperpc on Sat, 2019-09-21 17:30 |
1 |
by TechAUmNu Mon, 2019-09-30 14:34 |
Third Party Hardware | |
|
VESC Keeps resetting from IWDT timeout_init() by gowrav on Thu, 2019-09-19 08:45 |
1 |
by gowrav Sun, 2019-09-29 16:49 |
General discussion | |
|
Raptor 2 by Phill Dixon on Sat, 2019-09-28 19:35 |
2 |
by Phill Dixon Sun, 2019-09-29 14:39 |
General discussion | |
|
Wand remote with non-Trampa boards by hans_maier on Fri, 2019-09-20 23:18 |
1 |
by frank Sat, 2019-09-28 21:46 |
General discussion |
Pages
