You are here
Feature Requests
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
SINE/COSINE Encoder Support by shaman » Mon, 2018-12-17 15:14 |
4 |
by district9prawn Mon, 2019-06-17 13:37 |
|
|
Dual control loop with magnetic encoders by wall0069 » Sun, 2019-06-02 05:39 |
0 |
by wall0069 Sun, 2019-06-02 05:39 |
|
|
ERPM Limit Update Over CAN by josh » Sun, 2019-06-02 01:48 |
1 |
by josh Sun, 2019-06-02 02:05 |
|
|
Trapezoidal Trajectory/Position Control by wewa » Sun, 2018-09-23 11:33 |
2 |
by Vishwa Brahmaiah Fri, 2019-05-24 19:10 |
|
|
Field Weakening by hexakopter » Wed, 2017-10-11 23:21 |
13 |
by paltatech Sun, 2019-05-12 17:11 |
|
|
Read erpm of motor through motor tachometer by jordanlow » Tue, 2019-04-30 15:18 |
0 |
by jordanlow Tue, 2019-04-30 15:18 |
|
|
Handbrake when activating brake standstill by Pimousse » Mon, 2017-09-11 09:50 |
13 |
by Chad Austin Sun, 2019-04-21 00:50 |
|
|
AC Induction Motor Control Support by shaman » Fri, 2019-04-12 17:50 |
1 |
by paltatech Sat, 2019-04-13 16:53 |
|
|
Support for AMC1301 powered from bootstrap by antonchromjak » Thu, 2019-04-04 22:46 |
2 |
by antonchromjak Fri, 2019-04-05 11:16 |
|
|
Lights control from the nrf remote and configuration tab in VESC TOOL by ma-j-sterelektron » Thu, 2019-03-21 15:18 |
0 |
by ma-j-sterelektron Thu, 2019-03-21 15:18 |
|
|
Enhance position and rpm control interface / protocol by brushlessjoe » Wed, 2019-03-20 21:54 |
0 |
by brushlessjoe Wed, 2019-03-20 21:54 |
|
|
Motion commands for controlling CNCs by andresv » Fri, 2017-09-08 10:35 |
2 |
by brushlessjoe Sun, 2019-03-17 21:29 |
|
|
Combat Robot Mods by BrianNave » Sun, 2019-02-24 17:03 |
0 |
by BrianNave Sun, 2019-02-24 17:03 |
|
|
Allow braking to override negative ramping time by Paul15578 » Wed, 2018-01-24 06:20 |
5 |
by benjamin Sat, 2019-02-23 10:14 |
|
|
Duty cycle mode with neutral by titoxd10001 » Fri, 2017-09-08 12:04 |
13 |
by Badkad Thu, 2018-12-27 13:22 |
|
|
Sensorless temperature compensation by ESCam » Fri, 2018-12-14 19:38 |
1 |
by ESCam Fri, 2018-12-14 19:40 |
|
|
Auto power shut down by Ecyclist » Thu, 2018-09-20 00:47 |
4 |
by sam.vanratt Sat, 2018-11-24 20:12 |
|
|
Vesc slow speed BLDC without coging by igisboard » Tue, 2018-10-09 18:38 |
1 |
by Dillon Mon, 2018-11-19 01:41 |
|
|
Better use of hall sensors. by ThierryGTLTS » Fri, 2017-10-20 17:18 |
2 |
by AfdhalAtiffTan Wed, 2018-10-24 02:16 |
|
|
Maximum Reverse Power Output for Power Generation by Tobias Kornmayer » Sun, 2017-10-29 02:48 |
6 |
by SaqibBajwa Thu, 2018-09-20 00:57 |
|
|
Show actual encoder RPM by Enak » Fri, 2017-09-08 01:05 |
2 |
by Roger Wolff Sun, 2018-09-16 09:47 |
|
|
Single shunt by andreas » Wed, 2018-09-12 22:17 |
0 |
by andreas Wed, 2018-09-12 22:17 |
|
|
Foc openloop soft start by Alan oldguy » Fri, 2018-09-07 03:05 |
0 |
by Alan oldguy Fri, 2018-09-07 03:05 |
|
|
Ramping and idle control by DougM » Sat, 2018-09-01 16:22 |
0 |
by DougM Sat, 2018-09-01 16:22 |
|
|
Raw encoder output from UART by sprockmonty » Mon, 2018-08-13 16:45 |
0 |
by sprockmonty Mon, 2018-08-13 16:45 |
Log in to post new content in the forum.
