You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Custom 12S VESC, motor jerks but wont start by nickw1881 on Sun, 2018-03-18 10:46 |
16 |
by TechAUmNu Wed, 2020-02-12 12:50 |
Third Party Hardware | |
|
Power switch on VESCT6+ (MK3) by henry10210 on Thu, 2019-12-26 00:47 |
8 |
by henry10210 Tue, 2020-02-11 15:48 |
VESC Original Hardware | |
|
Current KP(Current controller proportional gain) by Geir Henriksen on Tue, 2019-04-30 10:51 |
1 |
by Ricardo Bosqui Tue, 2020-02-11 15:12 |
General discussion | |
|
VESC Tool 2.02 UI Issues? by AberrantRobotics on Tue, 2020-02-04 16:08 |
1 |
by frank Mon, 2020-02-10 18:16 |
General discussion | |
|
How does VESC measure the flux? by Jongwon on Thu, 2020-01-30 04:45 |
2 |
by pf26 Mon, 2020-02-10 16:18 |
General discussion | |
|
What's general algorithm of firmware? by Furkan Kaşku on Mon, 2020-02-10 09:20 |
1 |
by vadicus Mon, 2020-02-10 10:20 |
General discussion | |
|
AHRS yaw drifting by henry10210 on Sun, 2020-02-09 01:13 |
by henry10210 Sun, 2020-02-09 01:13 |
VESC Firmware | ||
|
Can larger BLDC motors be controlled with VESC? by Heimfried on Sun, 2020-02-02 21:29 |
3 |
by Heimfried Thu, 2020-02-06 22:39 |
General discussion | |
|
MK3 branch in bldc repo? by henry10210 on Tue, 2019-12-31 23:49 |
1 |
by Teslafly Thu, 2020-02-06 21:22 |
VESC Firmware | |
|
Extremely slow FW update (Vesc Tool 2.2) by fender90 on Mon, 2020-02-03 19:26 |
by fender90 Wed, 2020-02-05 05:22 |
VESC Tool | ||
|
Servo Mode / ODrive on VESC by JulianT on Tue, 2020-02-04 09:19 |
by JulianT Tue, 2020-02-04 09:19 |
General discussion | ||
|
Need Wiring Diagram for 2xLipo Series with 2x MK3 Button Start by adamchicago on Thu, 2020-01-30 19:47 |
1 |
by frank Sat, 2020-02-01 20:27 |
General discussion | |
|
VESC tool max current by marcus.herold on Wed, 2020-01-29 19:30 |
3 |
by marcus.herold Thu, 2020-01-30 16:26 |
VESC Tool | |
|
Hot swapping of controller parameters by Victor Bruun on Wed, 2020-01-29 09:22 |
1 |
by vadicus Wed, 2020-01-29 20:46 |
Feature Requests | |
|
GSESC - Schematic review for new Hardware by CTSchorsch on Wed, 2020-01-29 15:41 |
by CTSchorsch Wed, 2020-01-29 15:41 |
Third Party Hardware | ||
|
How to start with vesc source code ? by cmarc on Tue, 2020-01-28 15:48 |
by cmarc Tue, 2020-01-28 15:48 |
General discussion | ||
|
How trottle input by wire? by Heimfried on Mon, 2020-01-27 17:49 |
2 |
by Heimfried Mon, 2020-01-27 21:43 |
General discussion | |
|
PPM mapping not working by Andytttt on Thu, 2020-01-09 05:58 |
1 |
by frank Mon, 2020-01-27 21:06 |
VESC Tool | |
|
PPM Configuration is Only Working While Connected to VESC Software by kyle45 on Wed, 2020-01-15 05:13 |
2 |
by frank Mon, 2020-01-27 21:03 |
VESC Tool | |
|
Standby - consumption when battery is conencted by derbe on Thu, 2019-09-26 14:07 |
4 |
by frank Mon, 2020-01-27 20:48 |
Feature Requests |
Pages
