You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Custom Hardware - FET shoot-through problem - oscilloscope captures by ben5243 on Tue, 2019-02-19 03:58 |
2 |
by TechAUmNu Sat, 2019-03-16 00:27 |
Third Party Hardware | |
|
VESC 6 DC motor Current limit? by ShortCircuit on Thu, 2019-02-07 21:56 |
14 |
by ShortCircuit Thu, 2019-03-14 19:34 |
General discussion | |
|
Guide for modifying firmware/ apps by Enak on Wed, 2017-09-06 17:24 |
3 |
by TechAUmNu Thu, 2019-03-14 17:38 |
General discussion | |
|
DRV8323 by Jessica on Thu, 2019-03-14 11:41 |
by Jessica Thu, 2019-03-14 11:42 |
General discussion | ||
|
Update FW using vesc tool over phone by SkaterBoy58 on Thu, 2019-03-14 05:33 |
by SkaterBoy58 Thu, 2019-03-14 05:33 |
VESC Tool | ||
|
Can I change control mode on the fly through the UART port? by spork on Wed, 2019-03-13 02:24 |
2 |
by spork Wed, 2019-03-13 15:41 |
General discussion | |
|
Fault finding on failed VESC by dmcke5 on Sun, 2019-02-17 01:57 |
2 |
by benjamin Wed, 2019-03-13 10:00 |
General discussion | |
|
Fault finding on failed VESC by dmcke5 on Sun, 2019-02-17 01:57 |
2 |
by benjamin Wed, 2019-03-13 10:00 |
Third Party Hardware | |
|
Standard CAN Protcol by bakhrt on Sat, 2019-03-09 20:36 |
1 |
by benjamin Wed, 2019-03-13 09:54 |
VESC Firmware | |
|
Input Setup Wizard Does Not Ask if Single or Multi VESC by kylemuramatsu on Wed, 2019-03-13 03:22 |
1 |
by benjamin Wed, 2019-03-13 09:38 |
General discussion | |
|
how do you arm your Vesc in arduino code? by the creator on Wed, 2019-03-13 01:11 |
by the creator Wed, 2019-03-13 01:33 |
General discussion | ||
|
Multi-turn position control with ABI encoder by vpl on Fri, 2019-02-15 13:25 |
1 |
by Gas_Sn4ke Tue, 2019-03-12 04:14 |
VESC Firmware | |
|
ADC pin voltage not zero by zoppp on Fri, 2019-02-08 23:44 |
12 |
by zoppp Tue, 2019-03-12 01:17 |
General discussion | |
|
VESC regenerating while RPM increased by olivierskypullc... on Fri, 2019-03-08 16:32 |
2 |
by olivierskypullc... Mon, 2019-03-11 10:45 |
General discussion | |
|
Sine Wave Frequency by speed3r on Mon, 2019-03-04 14:11 |
5 |
by TheFallen Sun, 2019-03-10 18:06 |
VESC Firmware | |
|
C80100 Outrunner 50kv does not want to spin. by Wormsnake on Sun, 2019-03-03 10:30 |
1 |
by TheFallen Sun, 2019-03-10 17:54 |
General discussion | |
|
Pedelec/eBike, PAS and sensors by sam.vanratt on Mon, 2018-11-19 11:46 |
2 |
by sam.vanratt Thu, 2019-03-07 20:22 |
General discussion | |
|
VESC6 PCB questions by ESCam on Sat, 2018-12-29 00:17 |
6 |
by TechAUmNu Thu, 2019-03-07 11:28 |
General discussion | |
|
PPM Over limit settings. by marto on Thu, 2019-03-07 05:35 |
1 |
by marto Thu, 2019-03-07 08:36 |
VESC Firmware | |
|
[SOLVED] RPM setting not working by olivierskypullc... on Wed, 2019-02-27 12:14 |
2 |
by olivierskypullc... Wed, 2019-03-06 10:10 |
VESC Tool |
Pages
