You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
FOC_Openloop terminal command via CAN? by Jackl on Mon, 2024-01-15 10:09 |
2 |
by Jackl Sun, 2024-03-17 21:27 |
VESC Firmware | |
|
Can i change the controller (LQFP64) with (LQFP100) with same Firmware? by GalihRiddle on Thu, 2019-09-05 13:44 |
2 |
by GalihRiddle Mon, 2019-09-09 13:22 |
General discussion | |
|
I'm trying a VESC in a RC car, but need help. by RandomloserDK on Sun, 2020-11-22 22:55 |
2 |
by RandomloserDK Tue, 2020-11-24 01:14 |
General discussion | |
|
Flipsky 75100 pro v2 ADC throttle stopped responding by JozoBozo on Tue, 2026-02-24 17:33 |
2 |
by JozoBozo Sun, 2026-03-01 13:40 |
General discussion | |
|
Update FW on multiple VESC pcbs using CAN issue by Offline on Wed, 2021-05-19 15:07 |
2 |
by Offline Wed, 2021-05-26 08:23 |
General discussion | |
|
Vesc - UAVCAN - Pixhawk by dbau on Tue, 2022-02-01 07:43 |
2 |
by Ahmad Abousaleh Fri, 2026-07-10 01:46 |
General discussion | |
|
vesc disconnected during detection by TonyYuan on Mon, 2023-06-26 09:17 |
2 |
by powerpedalph Thu, 2025-04-24 07:51 |
VESC Firmware | |
|
VESC Express TCP connect with iOS not possible by johannes.b on Mon, 2024-09-02 19:51 |
2 |
by johannes.b Sat, 2024-09-07 13:56 |
General discussion | |
|
Sudden motor stop by dmcke5 on Wed, 2018-08-15 13:50 |
2 |
by andreas Thu, 2018-09-06 20:48 |
General discussion | |
|
Cut off after reaching Max. Duty Cycle by toboli on Thu, 2023-06-01 22:54 |
2 |
by toboli Sat, 2023-07-01 13:32 |
General discussion | |
|
Flipsky 75100 Pro V2.0 + Ninebot Max G2 motor: FOC auto-detection failure by Killbot283 on Fri, 2026-06-26 14:49 |
2 |
by nikolaygenov79 Fri, 2026-07-03 13:34 |
Third Party Hardware | |
|
Brake lever Cutoff switch seperate from Regen braking/throttle wheel by SuperSpeed Scooter on Thu, 2022-11-03 19:13 |
2 |
by oangelo Wed, 2023-01-11 12:25 |
General discussion | |
|
GPIO Pins on VESC? by phils on Sat, 2022-10-22 17:58 |
2 |
by istvan.szell@gm... Tue, 2024-09-17 12:07 |
General discussion | |
|
Is my custom motor inductance too low? by perpetum on Wed, 2020-11-04 18:01 |
2 |
by perpetum Sat, 2020-11-28 18:28 |
Third Party Hardware | |
|
Connect VESC to Keyboard/Wireless Joystick by sanketh1691 on Mon, 2021-10-04 20:58 |
2 |
by sanketh1691 Wed, 2021-10-06 18:58 |
VESC Tool | |
|
Reverse polarity with 12V battery on Vesc 6, now giving fault codes by Kokonenen on Tue, 2023-03-28 13:45 |
2 |
by frank Wed, 2023-03-29 09:56 |
General discussion | |
|
Is there a workaround to set regen voltage, not current? by Gsorter on Sat, 2023-03-11 17:59 |
2 |
by Gsorter Sat, 2023-03-11 23:48 |
General discussion | |
|
Firmware 3.37 too old, unable to Connect VESC_Tool by Nico Isn on Wed, 2018-04-18 11:17 |
2 |
by Nico Isn Fri, 2018-04-20 16:31 |
VESC Firmware | |
|
Vesc Tool not opening on windows computer by maccert on Sat, 2019-03-02 11:04 |
2 |
by Luca Torani Sun, 2019-03-03 20:32 |
VESC Tool | |
|
Gyro/Accel utilisation for built in Alarm ?! :D by yoodog on Tue, 2021-03-30 00:48 |
2 |
by yoodog Tue, 2021-03-30 01:07 |
General discussion |
Pages
