You are here

VESC6 Beta

Pages

Topic / Topic starter Replies Last postsort ascending
Sticky topic Sticky: WARNINGs!! What you should not do!
by frank » Fri, 2017-06-09 00:55
7
by frank
Wed, 2019-11-06 10:59
Sticky topic Sticky: Failures so far and how to prevent them
by benjamin » Wed, 2017-07-05 13:07
7
by frank
Mon, 2018-09-17 20:49
Sticky topic Sticky: First firmware update
by benjamin » Fri, 2017-06-09 13:56
1
by al4alan@gmail.com
Mon, 2018-04-09 13:07
Sticky topic Sticky: VESC Tool for old hardware
by benjamin » Fri, 2017-07-07 11:49
17
by frank
Mon, 2017-10-09 15:56
Sticky topic Sticky: VESC BETAs HAVE WRONG LABEL PRINTED TO SENSOR PORT
by hexakopter » Thu, 2017-06-08 22:49
5
by frank
Thu, 2017-06-22 23:00
Sticky topic Sticky: MANUAL
by frank » Sat, 2017-06-10 00:29
2
by frank
Wed, 2017-06-14 16:46
Hot topic ABS Over Current Fault
by josh » Wed, 2017-06-21 20:37
26
by TechAUmNu
Thu, 2020-08-27 12:08
Normal topic DIY Vesc 75/300 motor not spinning
by motordriver111 » Mon, 2020-08-03 16:39
7
by motordriver111
Sun, 2020-08-23 08:37
Normal topic Braking current after high-speed coast
by ProgramThyself » Sun, 2020-08-23 06:02
0
by ProgramThyself
Sun, 2020-08-23 06:02
Normal topic CANBUS communication documentation
by Dillon » Sun, 2017-08-27 17:50
7
by Tinkerer
Fri, 2020-08-14 10:52
Normal topic VESC 6+ Altium File Audit
by Hovav » Wed, 2020-04-15 09:03
2
by Danny Bokma
Thu, 2020-06-11 20:41
Normal topic Stalled startup.
by Roger Wolff » Mon, 2017-06-19 15:52
5
by TechAUmNu
Thu, 2020-06-11 10:54
Hot topic Chibios/RT Virtual Com Port Driver.
by Sanjoy » Wed, 2017-06-07 22:53
15
by bb67
Tue, 2020-04-07 22:14
Hot topic VESC on multirotors
by jlcortex » Sat, 2018-03-10 01:02
33
by Taury55
Thu, 2020-02-27 19:40
Normal topic FOC control Speed and D-axis current oscillations
by sxv9616 » Tue, 2019-12-03 22:14
2
by sxv9616
Thu, 2019-12-05 17:12
Normal topic Can't connect to slave vesc via master usb in vesc-tool -SOLVED-
by rich » Mon, 2017-07-24 13:31
13
by fadez
Tue, 2019-09-17 14:11
Normal topic VESC 6.0 Data Logging?
by josh » Fri, 2017-06-30 00:00
11
by e-nduro
Sun, 2019-06-30 22:35
Hot topic UART working great at low current, terrible at high current
by Dillon » Sat, 2018-03-17 04:17
23
by Dillon
Sat, 2019-01-19 04:06
Normal topic Problem with encoder readings with arduino
by ruthvikchanda » Thu, 2018-12-06 07:04
0
by ruthvikchanda
Thu, 2018-12-06 07:04
Hot topic Help with Built-in NRF24 and custom remote
by solidgeek » Thu, 2017-06-15 00:35
15
by m.juan
Mon, 2018-07-02 18:06
Normal topic Dead VESC6 due to shot from UBEC, repair possible?
by Boesila » Sat, 2018-04-14 11:35
9
by benjamin
Tue, 2018-06-26 14:37
Normal topic Dead VESC - Vibration?
by Shannon Talbot » Mon, 2018-05-14 02:28
1
by benjamin
Mon, 2018-05-14 10:37
Normal topic VESC6 firmware update fail
by DougM » Fri, 2017-09-01 03:09
5
by frank
Wed, 2018-05-02 14:39
Normal topic OVER CURRENT without over current?
by Oyta » Thu, 2018-04-19 23:26
3
by TheFallen
Sun, 2018-04-22 14:43
Normal topic Vesc 6 Hardware layout releasing "in the near future"
by david_hickox » Wed, 2018-03-07 04:42
2
by TechAUmNu
Wed, 2018-04-04 21:11

Pages

New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - VESC6 Beta