You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Access to balance fault settings when using other apps for control. by crutch on Tue, 2022-03-22 11:14 |
1 |
by auspiciouszesty Mon, 2022-06-06 10:32 |
Feature Requests | |
|
VESC as generator - settings confirmation by justinlsquire on Mon, 2022-06-06 02:44 |
by justinlsquire Mon, 2022-06-06 02:44 |
General discussion | ||
|
fsesc 4.20 CAN bus not detecting by LeonD on Sat, 2021-05-08 15:44 |
3 |
by MartyMcFlyFord Sat, 2022-06-04 16:54 |
VESC Tool | |
|
Flipsky 75200 with 80100 80kv by ors150 on Tue, 2021-09-14 20:03 |
2 |
by Oded Mazor Sat, 2022-06-04 15:17 |
General discussion | |
|
DIYElectricSkateboard.com Torque Board Street: DOA by epretorious on Thu, 2022-06-02 17:54 |
3 |
by frank Sat, 2022-06-04 11:50 |
Third Party Hardware | |
|
Force Sensor for a e-skateboard by beadon on Sat, 2022-06-04 05:08 |
1 |
by frank Sat, 2022-06-04 11:24 |
Feature Requests | |
|
VESC tool for windows by djevIen on Mon, 2019-06-17 08:02 |
2 |
by frank Fri, 2022-06-03 21:33 |
VESC Tool | |
|
Abs over current by Phill Dixon on Fri, 2022-06-03 17:26 |
by Phill Dixon Fri, 2022-06-03 17:26 |
General discussion | ||
|
Two Vesc6 MKV twin arrays ESC's - BMS CAN BUS connectivity by Spaceman on Fri, 2022-05-27 16:22 |
3 |
by Spaceman Fri, 2022-06-03 15:36 |
General discussion | |
|
Issues with VESC 75/300 and VESC-Tool V3.01 by hpb66 on Fri, 2022-06-03 09:15 |
by hpb66 Fri, 2022-06-03 09:15 |
VESC Tool | ||
|
I need clarification on connecting a Magura 0-5k Ohm Pot Twist Throttle to Tronic 250 VESC. by notahorse on Fri, 2022-06-03 08:13 |
by notahorse Fri, 2022-06-03 08:13 |
General discussion | ||
|
Turn on VESC via CAN Message by castiaum on Thu, 2022-06-02 12:17 |
1 |
by frank Thu, 2022-06-02 15:14 |
VESC Firmware | |
|
Regen Braking not working by James Hamilton on Thu, 2022-05-26 16:08 |
4 |
by frank Wed, 2022-06-01 18:14 |
VESC Tool | |
|
Segway tuning for a project using 2 VESC based ESCs by Clayton Haight on Wed, 2022-06-01 05:03 |
1 |
by frank Wed, 2022-06-01 11:04 |
General discussion | |
|
VESC HD60 Single version by lacondro on Tue, 2022-05-31 07:37 |
1 |
by frank Tue, 2022-05-31 07:48 |
VESC Original Hardware | |
|
problem with FOC current controller by masifsr on Sat, 2022-05-28 21:34 |
1 |
by Gatze Mon, 2022-05-30 18:34 |
VESC Firmware | |
|
Sourcing vesc hardware without paying ”brexit tax”? by st0r on Thu, 2022-05-26 05:24 |
3 |
by frank Mon, 2022-05-30 07:57 |
General discussion | |
|
Range not showing accurately by th3jonathan on Tue, 2022-05-24 17:43 |
5 |
by frank Mon, 2022-05-30 07:53 |
General discussion | |
|
Need some help on motor config and app config for Flypsky 65161 motor with FSESC75200 75V by freedomBoogie on Thu, 2021-03-04 09:30 |
2 |
by JoeSwe Sun, 2022-05-29 17:26 |
General discussion | |
|
Dual Motor Setup Wizard Not working 1.08 by captclearleft on Tue, 2019-04-16 01:05 |
5 |
by buggermenot Sat, 2022-05-28 15:11 |
VESC Tool |
Pages
