You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Version 2.03 won't open by marialoise on Fri, 2020-03-13 20:24 |
5 |
by pwilkinson91 Tue, 2023-06-27 22:07 |
VESC Tool | |
|
Can someone verify this by jsbenson on Mon, 2023-06-26 09:22 |
by jsbenson Tue, 2023-06-27 07:50 |
General discussion | ||
|
What is ADC3 used for in VESC6 by Tilman Baumann on Tue, 2018-04-10 11:12 |
3 |
by Gos1 Mon, 2023-06-26 13:56 |
VESC Original Hardware | |
|
(Watchdog) - Resets with multipole engine. by edilger on Mon, 2023-06-26 12:33 |
by edilger Mon, 2023-06-26 12:33 |
VESC Firmware | ||
|
Switching control scheme during opertion by Ben Murton on Tue, 2023-01-31 02:57 |
1 |
by Gos1 Mon, 2023-06-26 12:07 |
General discussion | |
|
New at VESC Tool by TheButaner on Sun, 2023-06-04 21:38 |
1 |
by Gos1 Mon, 2023-06-26 11:37 |
General discussion | |
|
Dual throttle inputs by olletj on Wed, 2022-08-10 23:56 |
2 |
by Gos1 Mon, 2023-06-26 11:34 |
General discussion | |
|
How to set up 60 degree hall sensors? by ryde6 on Sat, 2021-06-05 12:45 |
1 |
by Jan Jaroš Sat, 2023-06-24 13:47 |
VESC Tool | |
|
switching power supply by MagicKey on Tue, 2023-01-17 04:01 |
2 |
by vadicus Fri, 2023-06-23 22:59 |
General discussion | |
|
limits to reprogramming VESCs by wjpremerlani on Wed, 2023-06-21 09:11 |
2 |
by wjpremerlani Thu, 2023-06-22 20:13 |
General discussion | |
|
Torque Ripples with AC Servo Motor and Trampa VESC6 MKI by Der6FingerJo on Mon, 2023-06-19 23:25 |
by Der6FingerJo Mon, 2023-06-19 23:25 |
VESC Original Hardware | ||
|
Error code 6 by PatWhite32 on Mon, 2023-06-19 23:15 |
by PatWhite32 Mon, 2023-06-19 23:15 |
General discussion | ||
|
Autodetection values way off by thewho on Sat, 2019-05-25 20:34 |
28 |
by vadicus Mon, 2023-06-19 20:22 |
General discussion | |
|
Problem cruise with Adaptor 2 by Dominator2 on Sun, 2023-06-18 10:43 |
1 |
by Dominator2 Sun, 2023-06-18 14:55 |
General discussion | |
|
Hoverboard Motor, Noisy after FW update, Anti Cogging, PID values for low rpm by JulianT on Mon, 2023-02-13 10:50 |
1 |
by NolanCash Fri, 2023-06-16 16:58 |
Projects incorporating VESC technology | |
|
RPM and torque control modes by srinath on Fri, 2023-06-16 10:52 |
by srinath Fri, 2023-06-16 10:54 |
General discussion | ||
|
Can bus and Arduino by Snabelost on Wed, 2023-06-14 10:30 |
2 |
by Snabelost Thu, 2023-06-15 08:37 |
General discussion | |
|
Data log field value detailed descriptions by Foilguy on Mon, 2023-06-12 20:59 |
1 |
by Foilguy Wed, 2023-06-14 16:12 |
VESC Tool | |
|
Vesc 75100 by Matteo Christian on Wed, 2023-05-31 13:32 |
by Matteo Christian Fri, 2023-06-09 12:08 |
General discussion | ||
|
Not sure if parameter update in VESC tool works by srinath on Thu, 2023-06-08 11:29 |
by srinath Thu, 2023-06-08 11:29 |
VESC Tool |
Pages
