You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
VESC & CAN Bus Communication to another MCU (NOT VESC) by Jack_Li on Thu, 2019-07-11 04:08 |
5 |
by David_1 Thu, 2022-08-11 22:08 |
VESC Firmware | |
|
step/dir by blueflower on Thu, 2020-01-16 04:15 |
5 |
by akkoxe Mon, 2022-08-08 06:34 |
General discussion | |
|
KV command in terminal ( how to determine kv of a motor ) by fessyfoo on Sat, 2020-05-09 21:21 |
1 |
by rafeh1 Mon, 2022-08-08 04:31 |
VESC Tool | |
|
Flipsky 75100 with Flipsky VX1 remote -- do I have the wiring right? (VESC4 connector) by SeguinM on Sun, 2022-08-07 15:32 |
by SeguinM Sun, 2022-08-07 15:32 |
Third Party Hardware | ||
|
iq sign reversal at high RPM (was: Duty cycle jumps to maximum when *lowering* current limit) by vadimz on Thu, 2022-06-23 14:00 |
4 |
by vadimz Sun, 2022-08-07 13:03 |
VESC Firmware | |
|
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings on Fri, 2022-08-05 11:06 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
General discussion | ||
|
Updated VESC 6 schematic request by ma-j-sterelektron on Mon, 2019-03-25 08:43 |
3 |
by Roby_88 Thu, 2022-08-04 12:43 |
General discussion | |
|
temperature compensation make sense？ by alexshen2012 on Thu, 2022-08-04 08:28 |
1 |
by alexshen2012 Thu, 2022-08-04 09:17 |
General discussion | |
|
FAULT_CODE_UNDER_VOLTAGE by alexantosh on Mon, 2021-11-29 09:26 |
9 |
by heravinluca Thu, 2022-08-04 04:19 |
VESC Tool | |
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset on Thu, 2022-08-04 01:44 |
by liminalsunset Thu, 2022-08-04 01:44 |
General discussion | ||
|
Different rpm when using 3 vesc with can-bus by ewakegermanyhq on Wed, 2022-08-03 17:03 |
by ewakegermanyhq Wed, 2022-08-03 17:03 |
VESC Tool | ||
|
Lanyard kill switch by craig w on Mon, 2022-01-03 09:30 |
3 |
by ewakegermanyhq Wed, 2022-08-03 16:55 |
General discussion | |
|
Under rated VESC for motor, problem? by Alistair Goodman on Wed, 2022-08-03 12:53 |
2 |
by Alistair Goodman Wed, 2022-08-03 15:27 |
General discussion | |
|
VESC BMS Hardware Reference Design by DubP on Fri, 2021-09-03 21:00 |
10 |
by frank Wed, 2022-08-03 14:34 |
VESC Original Hardware | |
|
Plz Help Me, im at the end of my rope.....(Flipsky 4.12) by curtiswooden35 on Wed, 2022-08-03 03:23 |
1 |
by frank Wed, 2022-08-03 14:32 |
VESC Tool | |
|
Custom 75_150 board noise and not synchronized by lacondro on Mon, 2022-08-01 09:06 |
1 |
by lacondro Tue, 2022-08-02 13:26 |
Third Party Hardware | |
|
VESC 100/250 won't go full duty cycle by TheBennis on Tue, 2022-06-14 05:33 |
6 |
by TheBennis Tue, 2022-08-02 04:25 |
VESC Original Hardware | |
|
Sensorless FOC with Duty Cycle will not stop spinning by moose09876 on Mon, 2022-08-01 18:08 |
by moose09876 Mon, 2022-08-01 18:08 |
General discussion | ||
|
Dynamic Braking with resistor by jwhall on Sun, 2022-07-31 19:58 |
by jwhall Sun, 2022-07-31 23:51 |
General discussion | ||
|
Controling the Vesc via Uart and Matlab? by Michael Hamm on Mon, 2022-01-24 16:47 |
1 |
by Fikret Sonmez Sat, 2022-07-30 06:14 |
General discussion |
Pages
