You are here

Active forum topics

Topic Replies Last postsort ascending Forum
Normal topic Trying to make motor-control work for predetermined motions, could use some help
by Davideo on Fri, 2019-08-16 01:20
1 by s0313045
Mon, 2019-08-19 05:12
General discussion
Normal topic Wrong Motor detection values after STM swap dual vesc 6
by Micro on Sun, 2019-08-18 01:59
by Micro
Sun, 2019-08-18 02:14
VESC Tool
Normal topic Simulating controller accurately
by TechAUmNu on Fri, 2019-08-16 15:35
by TechAUmNu
Fri, 2019-08-16 15:35
General discussion
Normal topic understanding switching frequency and dutycycle
by speed3r on Thu, 2019-08-08 13:36
3 by speed3r
Thu, 2019-08-15 09:26
General discussion
Normal topic VESC 4.12 - Data loss on power off
by da_rul0r on Wed, 2019-08-14 16:43
2 by da_rul0r
Thu, 2019-08-15 08:33
VESC Original Hardware
Normal topic Need help to configure the regenerative brake ...
by Loops on Mon, 2019-08-12 19:43
2 by Loops
Wed, 2019-08-14 18:07
General discussion
Normal topic Add serial port
by CTSchorsch on Wed, 2019-08-14 15:30
by CTSchorsch
Wed, 2019-08-14 15:30
VESC Firmware
Normal topic How Can I make the tool work with FW 3.5 instead of just 3.58?
by ipbyrne on Fri, 2019-07-26 18:20
3 by frank
Wed, 2019-08-14 14:01
VESC Tool
Normal topic Help setting up dual vesc via CANBUS
by Jaystro16 on Sun, 2019-08-04 01:39
1 by frank
Wed, 2019-08-14 13:55
VESC Tool
Normal topic MAYTECH ESC6 200A runs fine on 6s, faults immediately on 12s
by mxpro32 on Sun, 2019-06-30 21:39
3 by TechAUmNu
Tue, 2019-08-13 10:21
Third Party Hardware
Normal topic MINI FOC from MakerX
by YUTW on Thu, 2019-08-08 11:17
1 by speed3r
Tue, 2019-08-13 10:17
Third Party Hardware
Normal topic Reverse ADC and UART
by ben_src on Mon, 2019-08-12 17:22
by ben_src
Mon, 2019-08-12 17:22
General discussion
Normal topic Problem report: VESC keeps running at full reverse throttle after PPM input returns to mid-stick
by chunkulator on Sun, 2019-08-11 00:34
by chunkulator
Sun, 2019-08-11 00:34
VESC Firmware
Normal topic Maytech 200A does not work in FOC, will a A200S work better?
by doom on Wed, 2019-08-07 20:40
1 by TechAUmNu
Fri, 2019-08-09 21:01
Third Party Hardware
Normal topic what do you guys think about this "curr_samp_volt "?
by jem on Thu, 2019-08-08 14:45
by jem
Thu, 2019-08-08 14:45
VESC Firmware
Normal topic VESC4 phase shunt
by Rico on Tue, 2019-05-21 16:09
3 by svs
Thu, 2019-08-08 08:41
VESC Firmware
Hot topic UART communication
by EthB on Wed, 2017-09-06 19:13
19 by stefcux
Thu, 2019-08-08 03:16
General discussion
Normal topic How to set a jog speed using an encoder
by AK6302019 on Wed, 2019-08-07 15:42
by AK6302019
Wed, 2019-08-07 15:42
General discussion
Normal topic VESC UART Espruino
by Gpole on Mon, 2019-05-20 12:25
2 by hughlloyd
Wed, 2019-08-07 06:22
VESC Firmware
Normal topic "Throttle" help
by benha on Wed, 2019-08-07 05:58
by benha
Wed, 2019-08-07 05:58
General discussion

Pages

Subscribe to Active forum topics