You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
VESC 6 with 3 phase shunts to ground instead by shaman on Wed, 2019-01-30 21:23 |
2 |
by shaman Thu, 2019-01-31 15:33 |
Third Party Hardware | |
|
Calculate HW_DEAD_TIME_VALUE by sunsam8 on Tue, 2019-01-29 01:47 |
1 |
by paltatech Thu, 2019-01-31 04:54 |
VESC Firmware | |
|
4.12 Phase current/voltage sense mix up. Need assistance please. by shaman on Tue, 2019-01-29 14:58 |
2 |
by shaman Tue, 2019-01-29 16:24 |
Third Party Hardware | |
|
Does the code right by jennyxcy2008 on Mon, 2019-01-28 02:57 |
7 |
by jennyxcy2008 Tue, 2019-01-29 04:52 |
VESC Firmware | |
|
Adjusting Beta Value for Motor Thermistor. by Ecyclist on Thu, 2018-12-06 23:22 |
12 |
by Ecyclist Tue, 2019-01-29 04:29 |
VESC Tool | |
|
Travis CI by paltatech on Tue, 2019-01-29 00:57 |
by paltatech Tue, 2019-01-29 00:57 |
VESC Firmware | ||
|
VESC Tool Instructions by brschaefer74 on Fri, 2019-01-25 03:49 |
4 |
by sam.vanratt Sat, 2019-01-26 12:52 |
General discussion | |
|
VESC and Motors for sale. by raess on Thu, 2019-01-24 22:41 |
by raess Thu, 2019-01-24 22:41 |
General discussion | ||
|
Connect both hall and incremental quadrature encoders by vpl on Tue, 2019-01-15 14:24 |
1 |
by galp Thu, 2019-01-24 14:25 |
General discussion | |
|
VESC on 48V 1500W HUB motor by jordanlow on Sat, 2019-01-12 14:52 |
4 |
by jordanlow Thu, 2019-01-24 04:14 |
VESC Original Hardware | |
|
Increasing low rpm torque in FOC mode by galp on Mon, 2019-01-21 18:15 |
1 |
by sam.vanratt Thu, 2019-01-24 00:02 |
General discussion | |
|
Separate Deadband for ADC2? by striderkent on Wed, 2019-01-23 16:31 |
by striderkent Wed, 2019-01-23 16:31 |
General discussion | ||
|
Angle offset detection by Gas_Sn4ke on Mon, 2019-01-21 07:09 |
by Gas_Sn4ke Mon, 2019-01-21 07:09 |
General discussion | ||
|
UART working great at low current, terrible at high current by Dillon on Sat, 2018-03-17 04:17 |
23 |
by Dillon Sat, 2019-01-19 04:06 |
VESC6 Beta | |
|
Change RPM of motor by Gas_Sn4ke on Wed, 2019-01-16 03:51 |
2 |
by Shaik Siraaj Thu, 2019-01-17 11:14 |
General discussion | |
|
Vesc 6 motor setup fault by Davo69URX on Wed, 2017-11-29 09:22 |
21 |
by Tresor Wed, 2019-01-16 12:38 |
General discussion | |
|
Upload bootloader to new MCU by Jessica on Fri, 2019-01-11 14:43 |
7 |
by Jessica Wed, 2019-01-16 09:07 |
General discussion | |
|
I put the wrong firmware (48) on my 4.12 vesc from Hobbyking by drawliphant on Mon, 2019-01-14 22:09 |
3 |
by drawliphant Wed, 2019-01-16 08:19 |
VESC Firmware | |
|
4kw BLDC hybrid system help by thardi10 on Tue, 2019-01-08 17:06 |
2 |
by frank Tue, 2019-01-15 22:15 |
General discussion | |
|
Firmware Modification Basics? Changing app_adc.c by striderkent on Tue, 2019-01-15 22:00 |
1 |
by striderkent Tue, 2019-01-15 22:05 |
VESC Firmware |
Pages
