You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
uROS support by neuromancer2701 on Wed, 2019-11-06 21:17 |
by neuromancer2701 Wed, 2019-11-06 21:17 |
Feature Requests | ||
|
load cell data logging by magnus.w on Thu, 2019-05-02 00:21 |
2 |
by Tom Burton Wed, 2019-11-06 16:43 |
VESC Tool | |
|
Description "Configuration for multiple VESCs via CAN-Bus" is missing in Documentation by Raphael on Wed, 2019-10-16 00:59 |
1 |
by frank Wed, 2019-11-06 13:00 |
VESC Tool | |
|
If firmware aint broke, dont fix it. by nickw1881 on Thu, 2019-10-31 07:32 |
3 |
by frank Wed, 2019-11-06 12:39 |
VESC Tool | |
|
WARNINGs!! What you should not do! by frank on Fri, 2017-06-09 00:55 |
7 |
by frank Wed, 2019-11-06 10:59 |
VESC6 Beta | |
|
75/300 connection issues FW3.6 by renaudbarbier on Fri, 2019-11-01 20:17 |
3 |
by frank Tue, 2019-11-05 09:18 |
General discussion | |
|
75/300 Large inrunner problem (video) by dk-odense on Mon, 2019-11-04 21:53 |
1 |
by frank Tue, 2019-11-05 09:06 |
General discussion | |
|
Electric moped self build. by Moped Mickey on Mon, 2019-10-28 18:15 |
1 |
by frank Mon, 2019-11-04 13:39 |
General discussion | |
|
VESC with 3 shunt by _johnny_ on Fri, 2019-11-01 18:57 |
by _johnny_ Fri, 2019-11-01 18:57 |
Third Party Hardware | ||
|
VESC hw_60 invert PWM. by _johnny_ on Fri, 2019-11-01 18:44 |
by _johnny_ Fri, 2019-11-01 18:47 |
Third Party Hardware | ||
|
USB Unable to connect by Bazeljet on Thu, 2019-10-10 06:02 |
5 |
by portnawake Mon, 2019-10-28 21:42 |
General discussion | |
|
VESC 75/300 + ~20kW motor , bms configuration problem... by gucho on Sat, 2019-10-26 14:45 |
4 |
by hockinsk Mon, 2019-10-28 21:33 |
General discussion | |
|
paltatech v0.2 HW not supported in latest firmware? by samuelis01 on Sun, 2019-10-27 22:52 |
by samuelis01 Sun, 2019-10-27 22:52 |
VESC Firmware | ||
|
Unable to flash firmware to VESC using OpenOCD by Bayne on Fri, 2019-10-25 02:34 |
by Bayne Fri, 2019-10-25 02:35 |
VESC Firmware | ||
|
Any issues with the DRV8323? by shaman on Thu, 2019-10-24 21:50 |
by shaman Thu, 2019-10-24 21:50 |
General discussion | ||
|
VESC - Motor will not start until a small kick is applied from a full stop despite using hall sensors by 010203040506070809 on Wed, 2019-10-23 23:12 |
by 010203040506070809 Wed, 2019-10-23 23:12 |
General discussion | ||
|
version of Vesc Tool for Flipsky 6.6 by Robert Adkins on Sun, 2019-09-29 18:13 |
3 |
by frank Wed, 2019-10-23 09:35 |
VESC Tool | |
|
EBESC 6.1 Remote wont connect and cant get past the error code port not recognized by flashg69777 on Tue, 2019-10-22 02:01 |
1 |
by frank Tue, 2019-10-22 11:13 |
Third Party Hardware | |
|
safety switch by Ralph Luckwaldt on Mon, 2019-10-21 13:15 |
1 |
by frank Mon, 2019-10-21 20:58 |
Feature Requests | |
|
Pulling fault codes without USB by shaman on Fri, 2019-10-18 15:13 |
5 |
by shaman Sun, 2019-10-20 22:54 |
General discussion |
Pages
