You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
VESC for turbomachine testing - max ERPM? by batdan on Tue, 2019-08-13 16:58 |
2 |
by batdan Tue, 2019-08-27 16:48 |
General discussion | |
Logging IMU Data over UART by stefan_novige on Mon, 2019-08-19 18:28 |
6 |
by pf26 Tue, 2019-08-27 13:44 |
General discussion | |
VESC CAN Status message interpretation by harsha008 on Wed, 2019-01-09 17:56 |
1 |
by bluesquall Tue, 2019-08-27 01:59 |
General discussion | |
Sensorless BLDC start problem by MikeStros on Tue, 2019-07-30 11:49 |
2 |
by dekafive Fri, 2019-08-23 21:46 |
General discussion | |
foc with encoder fails to run smoothly by jdn on Thu, 2019-08-22 12:26 |
by jdn Thu, 2019-08-22 15:47 |
General discussion | ||
Is it possible to stop a motor at one exact desired location without hall sensor? by vimi94 on Thu, 2019-08-15 10:58 |
2 |
by vimi94 Tue, 2019-08-20 13:37 |
VESC Tool | |
Problems with flashing firmware to FLIPSKY ESC by xx11xx on Wed, 2019-08-14 18:10 |
1 |
by kinzma Tue, 2019-08-20 07:56 |
VESC Firmware | |
Vesc to Uart (Nextion display) by g1tana on Mon, 2019-08-19 15:29 |
by g1tana Mon, 2019-08-19 15:30 |
General discussion | ||
Trying to make motor-control work for predetermined motions, could use some help by Davideo on Fri, 2019-08-16 01:20 |
1 |
by s0313045 Mon, 2019-08-19 05:12 |
General discussion | |
Wrong Motor detection values after STM swap dual vesc 6 by Micro on Sun, 2019-08-18 01:59 |
by Micro Sun, 2019-08-18 02:14 |
VESC Tool | ||
Simulating controller accurately by TechAUmNu on Fri, 2019-08-16 15:35 |
by TechAUmNu Fri, 2019-08-16 15:35 |
General discussion | ||
understanding switching frequency and dutycycle by speed3r on Thu, 2019-08-08 13:36 |
3 |
by speed3r Thu, 2019-08-15 09:26 |
General discussion | |
VESC 4.12 - Data loss on power off by da_rul0r on Wed, 2019-08-14 16:43 |
2 |
by da_rul0r Thu, 2019-08-15 08:33 |
VESC Original Hardware | |
Need help to configure the regenerative brake ... by Loops on Mon, 2019-08-12 19:43 |
2 |
by Loops Wed, 2019-08-14 18:07 |
General discussion | |
Add serial port by CTSchorsch on Wed, 2019-08-14 15:30 |
by CTSchorsch Wed, 2019-08-14 15:30 |
VESC Firmware | ||
How Can I make the tool work with FW 3.5 instead of just 3.58? by ipbyrne on Fri, 2019-07-26 18:20 |
3 |
by frank Wed, 2019-08-14 14:01 |
VESC Tool | |
Help setting up dual vesc via CANBUS by Jaystro16 on Sun, 2019-08-04 01:39 |
1 |
by frank Wed, 2019-08-14 13:55 |
VESC Tool | |
MAYTECH ESC6 200A runs fine on 6s, faults immediately on 12s by mxpro32 on Sun, 2019-06-30 21:39 |
3 |
by TechAUmNu Tue, 2019-08-13 10:21 |
Third Party Hardware | |
MINI FOC from MakerX by YUTW on Thu, 2019-08-08 11:17 |
1 |
by speed3r Tue, 2019-08-13 10:17 |
Third Party Hardware | |
Reverse ADC and UART by ben_src on Mon, 2019-08-12 17:22 |
by ben_src Mon, 2019-08-12 17:22 |
General discussion |