You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Using VESC for a Linear Motor by Toshi Sharma on Wed, 2022-01-12 13:11 |
by Toshi Sharma Wed, 2022-01-12 13:11 |
General discussion | ||
|
PWM timer issues on high voltage by pegasus-aero on Tue, 2022-01-04 01:39 |
3 |
by pegasus-aero Thu, 2022-01-13 00:37 |
Third Party Hardware | |
|
I cant get my scooter to work correct it make some strange sounds by vallsta on Sun, 2021-05-16 03:19 |
39 |
by svs Thu, 2022-01-13 07:53 |
General discussion | |
|
E-bike with Ubox board by tailele on Wed, 2020-11-18 11:48 |
6 |
by kevingraehl Thu, 2022-01-13 09:24 |
Third Party Hardware | |
|
Failure in Motor Set Up by Toshi Sharma on Tue, 2022-01-11 15:19 |
9 |
by frank Thu, 2022-01-13 14:15 |
General discussion | |
|
I Need Some Guidance With My Schematic 16s 50a by qwerasdf on Sat, 2022-01-01 15:04 |
6 |
by mckenzie.keith Fri, 2022-01-14 04:39 |
Third Party Hardware | |
|
BLDC_SPEED_CONTROL_CURRENT by salviador on Fri, 2022-01-14 16:32 |
by salviador Fri, 2022-01-14 16:32 |
VESC Firmware | ||
|
Rough Motor Running When USB Cable At Vesc Tool is Disconnected by David Cunliffe on Sun, 2022-01-16 11:42 |
11 |
by David Cunliffe Sun, 2022-01-16 15:32 |
General discussion | |
|
ESC FS75100 by myck33 on Fri, 2021-12-31 14:17 |
2 |
by jaykup Sun, 2022-01-16 22:43 |
VESC Firmware | |
|
Need Help with single FSESC running a BDUAV 6384 120KV & 12v SLA Batt Setup by KJB on Fri, 2022-01-07 02:43 |
1 |
by skyline1970 Tue, 2022-01-18 10:39 |
General discussion | |
|
CAN bus rate, Flipsky Mini FSESC6.7 by christian.lees on Tue, 2022-01-18 22:57 |
by christian.lees Tue, 2022-01-18 22:57 |
General discussion | ||
|
Best practice for controlling VESC with high speed PWM by arsenix on Sun, 2022-01-09 18:29 |
1 |
by skyline1970 Wed, 2022-01-19 09:39 |
General discussion | |
|
Did I damage My Vesc? by Kent Church on Tue, 2022-01-11 04:47 |
1 |
by skyline1970 Wed, 2022-01-19 09:46 |
General discussion | |
|
firm ware error 75_300 by yuri12 on Wed, 2022-01-19 09:50 |
1 |
by frank Wed, 2022-01-19 13:46 |
VESC Firmware | |
|
Stream UART Telemetry without a Request by AlexBenn on Thu, 2022-01-20 02:47 |
by AlexBenn Thu, 2022-01-20 02:47 |
VESC Firmware | ||
|
questions about "RUN DETECTION" by yuri12 on Thu, 2022-01-20 04:30 |
by yuri12 Thu, 2022-01-20 04:30 |
VESC Tool | ||
|
Max OSX version by emmaanuel on Tue, 2017-09-05 13:03 |
6 |
by briona112 Thu, 2022-01-20 05:27 |
VESC Tool | |
|
Anti cogging, suppressing torque ripple? by Alistair Goodman on Wed, 2022-01-19 11:33 |
4 |
by Alistair Goodman Thu, 2022-01-20 11:11 |
General discussion | |
|
Vesc Tool Mobile can't update Vesc Firmware by Happy Giraffe on Wed, 2022-01-19 21:48 |
2 |
by Happy Giraffe Thu, 2022-01-20 23:50 |
VESC Tool | |
|
PAS app: limit current depending on actual velocity by dpeinado on Fri, 2022-01-21 13:49 |
by dpeinado Fri, 2022-01-21 13:49 |
VESC Firmware |
Pages
