You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Turnigy Sk8 ESC - pulls voltage to zero by mnetterberg on Wed, 2021-09-29 10:17 |
1 |
by skyline1970 Mon, 2021-11-01 07:55 |
Third Party Hardware | |
|
VESC Tool crashes when loading/saving motor/app config by bkyrevolution on Thu, 2023-03-02 20:27 |
1 |
by jimtzer Mon, 2023-03-13 00:30 |
VESC Tool | |
|
PPM+UART: Priority to UART on HW6? by Filcas on Sat, 2021-04-03 11:05 |
1 |
by mark99 Sun, 2021-07-04 13:15 |
VESC Development and Beta Testing | |
|
Serial port errors with VESC Tool 3.00 and Flipsky FSESC 7550 by mckenzie.keith on Thu, 2022-01-06 02:24 |
1 |
by mckenzie.keith Thu, 2022-01-06 18:54 |
VESC Tool | |
|
Foc limit at 25v by Thegolfer on Wed, 2020-08-19 18:51 |
1 |
by Thegolfer Wed, 2020-08-19 19:56 |
General discussion | |
|
Unidentified Part by amit_bhar on Thu, 2021-12-23 23:43 |
1 |
by skyline1970 Fri, 2021-12-24 09:22 |
Third Party Hardware | |
|
Sensored BLDC problem - RPM spikes by arsenix on Thu, 2018-12-27 05:41 |
1 |
by arsenix Thu, 2019-01-03 03:29 |
VESC Firmware | |
|
Problem cruise with Adaptor 2 by Dominator2 on Sun, 2023-06-18 10:43 |
1 |
by Dominator2 Sun, 2023-06-18 14:55 |
General discussion | |
|
Torque Ramp Rate whilst in FOC by J_W97 on Mon, 2022-03-14 11:50 |
1 |
by skyline1970 Mon, 2022-03-14 20:29 |
General discussion | |
|
status message by riku on Thu, 2022-11-17 05:31 |
1 |
by frank Thu, 2022-11-17 17:55 |
General discussion | |
|
Vesc4 have 2 Analog output pins? by greensightag.com on Sat, 2018-05-12 00:42 |
1 |
by Roger Wolff Tue, 2018-05-15 10:51 |
VESC Original Hardware | |
|
Two VESCs with servo-out firmware by _saeed_arabi_ on Fri, 2019-12-13 22:22 |
1 |
by frank Thu, 2019-12-19 21:34 |
General discussion | |
|
ADC throttle lock. by Billy_Wiz on Mon, 2022-10-31 00:57 |
1 |
by vadicus Mon, 2022-10-31 19:51 |
General discussion | |
|
Control via UART and connect to VESC Tool using BLE by Seudo on Sun, 2023-12-17 21:34 |
1 |
by vadicus Thu, 2024-01-11 23:00 |
General discussion | |
|
Controling two motors with Dual FSESC6.6 in two directions by Rafal on Sat, 2021-10-16 13:47 |
1 |
by frank Mon, 2021-10-18 14:43 |
General discussion | |
|
Acceleration ramping using UART communication with arduino on VTool 6.0 by Kokonenen on Tue, 2023-04-04 11:48 |
1 |
by Kokonenen Tue, 2023-04-04 14:30 |
VESC Tool | |
|
No Option for Master or Slave on SetUp Input? by trickleung91 on Sun, 2019-06-30 09:06 |
1 |
by frank Sun, 2019-07-21 18:46 |
General discussion | |
|
Motor parameters constantly changing. by Alistair Goodman on Tue, 2022-09-06 15:57 |
1 |
by Alistair Goodman Wed, 2022-09-07 10:04 |
General discussion | |
|
PPM Output unavailable, or not functional - Vesc6.4 by solbergen on Tue, 2018-02-27 23:45 |
1 |
by benjamin Wed, 2018-02-28 11:55 |
VESC6 Beta | |
|
Dual motor for a small boat by Snabelost on Wed, 2022-08-24 10:58 |
1 |
by Snabelost Wed, 2022-08-24 13:56 |
General discussion |
Pages
