You are here

VESC Tool

Topic / Topic starter Replies Last postsort ascending
Normal topic Version 3.01 destroyed version 2.06 too
by Knaubel » Sun, 2022-05-15 21:23
6
by Knaubel
Wed, 2022-05-18 16:16
Normal topic Rough acceleration - BLDC & FOC
by Loose Nickers » Tue, 2020-02-11 07:56
9
by MC_DIY_Beginner
Mon, 2022-05-16 13:34
Normal topic ConfBackup, Where does it save it
by mikemoy » Tue, 2021-09-07 16:25
1
by ndp
Thu, 2022-05-12 20:25
Normal topic VESC100/250 - motor current setting ignored?
by tobiokanobi » Mon, 2022-05-02 13:27
3
by frank
Tue, 2022-05-03 20:54
Normal topic Vesc can't connect to vesc tool
by Roansky1 » Sat, 2022-04-30 13:05
3
by frank
Tue, 2022-05-03 20:52
Normal topic Use sensors on the output shaft of a motor attached to a large gear ratio gearbox
by davidq1688 » Wed, 2022-04-27 05:23
1
by tobiokanobi
Thu, 2022-04-28 14:48
Normal topic VESC Tool speed control overshoot
by PKmita » Tue, 2022-04-26 16:05
0
by PKmita
Tue, 2022-04-26 16:12
Normal topic experiment tab rpm ramp up and dual separate motor control
by tobiokanobi » Thu, 2022-04-14 20:20
5
by tobiokanobi
Tue, 2022-04-26 15:32
Normal topic Lisp scripting questions/suggestions/remarks
by Gatze » Sun, 2022-04-24 12:13
0
by Gatze
Sun, 2022-04-24 13:00
Normal topic VESC Tool app min hardware requirements
by flix » Sat, 2022-04-16 22:13
0
by flix
Sat, 2022-04-16 22:13
Normal topic Smart Reverse Minimum Erpm
by ZenRides » Wed, 2022-02-16 05:36
4
by nabil sassi
Tue, 2022-04-12 23:21
Normal topic Feature request: Raw hall data.
by Roger Wolff » Mon, 2018-06-11 15:49
4
by blubbi321
Tue, 2022-03-29 16:32
Normal topic foc openloop not starting motor on higher erpm
by Alan oldguy » Thu, 2018-09-06 08:43
8
by technicc
Mon, 2022-03-28 09:23
Normal topic 5000 rpm BLDC, 1600 rpm FOC
by scubersteve » Mon, 2022-03-21 03:10
1
by skyline1970
Fri, 2022-03-25 18:45
Hot topic Failure to download VESC Tool
by CallumMac » Tue, 2022-01-25 02:38
26
by Ian Watts
Wed, 2022-03-16 12:25
Normal topic VESC tool windows 10 connection via bluetooth
by th0masrtg » Thu, 2020-09-24 14:20
11
by sp3swj
Tue, 2022-03-15 03:08
Normal topic Upgrade the Bootloader?
by erikfed » Tue, 2022-03-08 20:32
0
by erikfed
Tue, 2022-03-08 20:32
Normal topic How to read the CAN message with CAN anlayzer
by yuri12 » Thu, 2022-03-03 18:21
0
by yuri12
Thu, 2022-03-03 18:21
Normal topic RT Data, v3.01, Amazon Fire Tablet (sideloaded)
by j.konrad » Thu, 2022-02-24 14:51
2
by j.konrad
Fri, 2022-02-25 14:14
Normal topic Writing value to both VESCs on FocFox Unity
by agraham » Wed, 2022-02-23 21:45
2
by benjamin
Thu, 2022-02-24 10:57
Normal topic Discrepancies between VESC Tool 3.01 Motor Settings & XML config file
by j.konrad » Sat, 2022-01-15 22:13
3
by benjamin
Mon, 2022-02-21 22:17
Normal topic Play Store - No App - Missing
by TooSlow2Care » Mon, 2022-02-14 20:18
3
by TooSlow2Care
Tue, 2022-02-15 19:40
Normal topic Vesc doesn't react to can messages from PC
by BorisDeroo » Fri, 2021-12-17 16:54
1
by yuri12
Wed, 2022-02-09 17:33
Normal topic single VESC 6+ controlled by CAN-bus
by vinci » Fri, 2021-07-09 15:42
1
by yuri12
Wed, 2022-02-09 17:23
Normal topic how to communication with arduino on vesc via CAN
by yuri12 » Tue, 2022-02-08 13:16
0
by yuri12
Tue, 2022-02-08 13:16
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - VESC Tool