You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
RT Data Logging by adas29 » Wed, 2023-04-26 22:59 |
0 |
by adas29 Wed, 2023-04-26 22:59 |
|
|
Can't spin both motors over CAN-bus by Kokonenen » Wed, 2023-04-19 11:19 |
3 |
by Kokonenen Fri, 2023-04-21 09:18 |
|
|
Parameters for efoil by vladek » Thu, 2023-04-20 12:54 |
0 |
by vladek Thu, 2023-04-20 12:54 |
|
|
Can't get Dual drive/CAN bus working by Xadiant » Sun, 2019-09-22 20:49 |
11 |
by Kokonenen Wed, 2023-04-19 11:10 |
|
|
How to adjust ADC1 parameters to adjust the speed (not working) by player107 » Fri, 2023-04-14 13:46 |
0 |
by player107 Fri, 2023-04-14 13:46 |
|
|
Position control without encoder by bearing » Tue, 2023-04-04 18:45 |
1 |
by bearing Thu, 2023-04-06 22:07 |
|
|
Acceleration ramping using UART communication with arduino on VTool 6.0 by Kokonenen » Tue, 2023-04-04 11:48 |
1 |
by Kokonenen Tue, 2023-04-04 14:30 |
|
|
VESC Tool crashes when loading/saving motor/app config by bkyrevolution » Thu, 2023-03-02 20:27 |
1 |
by jimtzer Mon, 2023-03-13 00:30 |
|
|
Throttle movement by Lasse » Tue, 2023-03-07 12:16 |
0 |
by Lasse Tue, 2023-03-07 12:16 |
|
|
Data logging for dual VESC on Android VESC-tool by elmardus » Wed, 2021-10-20 16:13 |
5 |
by SamuL Fri, 2023-02-17 00:55 |
|
|
Detection failed. Reason: Sensor detection failed by Lilian_CASTEL » Tue, 2020-11-24 11:31 |
8 |
by electricfox Thu, 2023-02-16 15:57 |
|
|
How to Enable kill switch support in Firmware 5.03 by iserai2r » Sat, 2022-02-05 13:59 |
5 |
by rodrigo.baronio Tue, 2023-02-14 02:27 |
|
|
VESC Tool Control Theory by AeonCypher » Sun, 2023-02-12 23:54 |
0 |
by AeonCypher Sun, 2023-02-12 23:54 |
|
|
Installing VESC Tool on Jetson Nano by mrburns19 » Tue, 2023-02-07 04:54 |
2 |
by mrburns19 Sun, 2023-02-12 01:44 |
|
|
Hall sensor data is all 0. What do? by Byproduct » Sat, 2023-01-14 14:39 |
0 |
by Byproduct Wed, 2023-02-08 11:21 |
|
|
Noobs need to update and / or configure old VESC 4.12 by Loops » Tue, 2023-02-07 11:49 |
0 |
by Loops Tue, 2023-02-07 11:49 |
|
|
duty cicle 95% but current not at max by rodrigo.baronio » Mon, 2023-02-06 15:52 |
0 |
by rodrigo.baronio Mon, 2023-02-06 15:52 |
|
|
Flipsky 75100foc motor detection sensor issue fails every crysaltemotor I've tried by Wheelzscootersinc » Fri, 2023-02-03 21:36 |
1 |
by tom355 Sun, 2023-02-05 11:11 |
|
|
Motor not running after applying SINE/COSINE settings by DHOUT » Fri, 2023-01-27 03:32 |
0 |
by DHOUT Fri, 2023-01-27 03:32 |
|
|
Motors spin up during detection but then won't move by jordan314 » Thu, 2019-02-21 09:18 |
12 |
by KDoc Tue, 2023-01-17 00:13 |
|
|
Firmware issues by salvasalce » Tue, 2022-12-13 16:12 |
2 |
by Lennart Duijn Mon, 2023-01-09 22:10 |
|
|
IMU not working after power cycle by Lennart Duijn » Mon, 2023-01-09 22:08 |
0 |
by Lennart Duijn Mon, 2023-01-09 22:08 |
|
|
I made a Boost Current Mod by JL2579 » Tue, 2018-01-23 18:28 |
10 |
by phiger Wed, 2022-12-21 11:19 |
|
|
How to control motor using VESC tool in computer at constant rpm? by vimi94 » Wed, 2019-05-01 12:56 |
3 |
by foreclosurecat Tue, 2022-12-06 22:36 |
|
|
Voltage measurement calibration? by pyryjansson » Tue, 2019-04-30 20:19 |
2 |
by frank Wed, 2022-11-30 09:55 |
Log in to post new content in the forum.
