You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
I made a Boost Current Mod by JL2579 » Tue, 2018-01-23 18:28 |
10 |
by phiger Wed, 2022-12-21 11:19 |
|
|
How to control motor using VESC tool in computer at constant rpm? by vimi94 » Wed, 2019-05-01 12:56 |
3 |
by foreclosurecat Tue, 2022-12-06 22:36 |
|
|
Voltage measurement calibration? by pyryjansson » Tue, 2019-04-30 20:19 |
2 |
by frank Wed, 2022-11-30 09:55 |
|
|
Serial Control From PC by aguzel » Fri, 2020-08-21 02:45 |
3 |
by Jens Mon, 2022-11-28 20:40 |
|
|
Cannot connect to vesc tool app by sharpshooterjd » Fri, 2022-07-29 23:39 |
1 |
by skyline1970 Sun, 2022-11-27 16:38 |
|
|
Flipsky 6.6 and VESC 5.3 don't mix? by Miniproto » Sun, 2022-11-27 16:34 |
0 |
by Miniproto Sun, 2022-11-27 16:34 |
|
|
Motor always accelerates to maximum speed by zapshe » Sun, 2022-09-11 03:46 |
1 |
by skyline1970 Sun, 2022-11-27 16:32 |
|
|
Taking 5-6 seconds for running motor under ADC mode by asnamp » Fri, 2022-06-24 13:02 |
1 |
by skyline1970 Thu, 2022-11-24 21:24 |
|
|
Problem to configure my esc with PWM-signal by Lucar » Wed, 2022-09-14 10:05 |
1 |
by skyline1970 Thu, 2022-11-24 20:26 |
|
|
PPM Pulselength mapping by Shaftdriver » Tue, 2022-10-04 19:50 |
1 |
by skyline1970 Thu, 2022-11-24 20:15 |
|
|
Vesc efficiency through log (.CSV) by th0masrtg » Tue, 2022-11-22 10:08 |
0 |
by th0masrtg Tue, 2022-11-22 10:08 |
|
|
Calibration ERROR with TLE5012B Magnetic encoder in ABI mode by cejota » Fri, 2022-03-25 03:19 |
2 |
by XieMaster Mon, 2022-11-14 05:32 |
|
|
Writing to slave vesc sometimes cause loss of can bus by meashman » Wed, 2022-07-20 01:08 |
2 |
by frank Thu, 2022-10-27 08:54 |
|
|
Unable to connect to vesc through can bus by Kupofty » Thu, 2022-10-20 16:24 |
0 |
by Kupofty Thu, 2022-10-20 16:24 |
|
|
TWO MOTOR SYSTEM by ronmotor » Mon, 2022-10-17 00:44 |
0 |
by ronmotor Mon, 2022-10-17 00:44 |
|
|
Detection failed. Reason: Flux linkage detection failed by Donnyten » Sun, 2022-10-09 20:31 |
2 |
by Donnyten Tue, 2022-10-11 02:56 |
|
|
PPM Pulselength mapping by Shaftdriver » Tue, 2022-10-04 17:18 |
0 |
by Shaftdriver Tue, 2022-10-04 17:18 |
|
|
HFI plot by Rick van der Sloot » Sun, 2022-10-02 22:26 |
0 |
by Rick van der Sloot Sun, 2022-10-02 22:26 |
|
|
Cruise Control button no longer working by Jobbel » Tue, 2017-09-05 01:10 |
1 |
by Jobbel Sun, 2022-09-25 16:36 |
|
|
Problem | Documentation images not showing by nadav182 » Mon, 2021-10-04 19:54 |
2 |
by lopezharding Wed, 2022-09-21 10:50 |
|
|
Help i can not setup my motors by jakson01 » Fri, 2022-09-09 18:37 |
0 |
by jakson01 Fri, 2022-09-09 18:37 |
|
|
FSESC seems to be speed limiting my motor by 5amsung4 » Sat, 2022-09-03 18:50 |
0 |
by 5amsung4 Mon, 2022-09-05 07:51 |
|
|
VESC tool for Android by Jaap » Fri, 2021-01-15 13:00 |
6 |
by Dan Dyse Fri, 2022-08-26 20:32 |
|
|
Is anyone else having the same problems by Jheckman » Mon, 2022-08-22 16:34 |
0 |
by Jheckman Mon, 2022-08-22 16:35 |
|
|
Is anyone else having the same problems by Jheckman » Mon, 2022-08-22 16:33 |
0 |
by Jheckman Mon, 2022-08-22 16:33 |
Log in to post new content in the forum.
