You are here
VESC Tool
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Did I lock myself out of bluetooth connection? by tylerskate » Sat, 2021-05-29 07:18 |
1 |
by Anordil Thu, 2021-08-05 00:06 |
|
|
Incorrect speed too high by Michele84 » Wed, 2021-07-21 15:48 |
0 |
by Michele84 Wed, 2021-07-21 15:48 |
|
|
Software safety features interrupting normal operation. by Tsomo » Wed, 2021-07-14 01:29 |
2 |
by Tsomo Wed, 2021-07-14 01:32 |
|
|
Overheating protection, voltage-/current-limitation etc. by kianK » Thu, 2021-04-15 07:23 |
2 |
by lilliamhoyle Wed, 2021-07-07 09:36 |
|
|
ADC throttle is accelerating th full throttle quickly by Buddah » Sun, 2019-09-15 23:32 |
4 |
by jimtzer Wed, 2021-06-30 17:54 |
|
|
Use Vesc-Tool to run two motors simultaneously via CAN by microlomaniac » Thu, 2021-06-17 11:55 |
2 |
by spacewalker Tue, 2021-06-22 08:23 |
|
|
Startup codes? by anthonys » Sat, 2021-06-19 17:29 |
0 |
by anthonys Sat, 2021-06-19 17:29 |
|
|
Motor whine with HFI? by christopher.h.poole » Mon, 2021-04-19 15:49 |
2 |
by christopher.h.poole Tue, 2021-06-15 21:18 |
|
|
NRF5X SWD Prog detection broken, always detects NRF52832 512K/64K by zippy » Sun, 2021-06-06 16:19 |
1 |
by zippy Sun, 2021-06-06 17:58 |
|
|
FOC configuration - Motor stalls during measurement by Lukinio » Wed, 2021-05-26 12:31 |
1 |
by Lukinio Wed, 2021-05-26 12:44 |
|
|
APP settings for Motor Position and RPM control with PPM by Marcos Bleda » Fri, 2021-05-21 10:47 |
0 |
by Marcos Bleda Fri, 2021-05-21 10:47 |
|
|
Update FW on multiple VESC pcbs using CAN issue by Offline » Thu, 2021-05-20 07:36 |
0 |
by Offline Thu, 2021-05-20 07:36 |
|
|
read RPM over CAN by nblange » Mon, 2021-05-03 20:43 |
0 |
by nblange Mon, 2021-05-03 20:43 |
|
|
Problem with VESC Tool vs BLDC FW version by Reidar Jortveit » Mon, 2021-04-26 14:39 |
1 |
by Reidar Jortveit Mon, 2021-04-26 14:49 |
|
|
no effect on set erpm/speed limit by xenon321 » Sat, 2021-04-24 20:43 |
0 |
by xenon321 Sun, 2021-04-25 16:53 |
|
|
DC Motor Settings (24v PowerWheels) by KirkusMaximus » Thu, 2021-04-22 00:17 |
0 |
by KirkusMaximus Thu, 2021-04-22 00:18 |
|
|
two motors one ppm for throttle and one for the direction? by Robby Ertmann » Wed, 2021-04-21 13:48 |
0 |
by Robby Ertmann Wed, 2021-04-21 13:48 |
|
|
throttle mapping: non-zero current at zero adc input? by FreddyForLaunch » Wed, 2021-04-14 21:48 |
0 |
by FreddyForLaunch Thu, 2021-04-15 09:00 |
|
|
Pc requirement to run vesc software by proget.snc » Mon, 2021-04-12 10:57 |
1 |
by benjamin Wed, 2021-04-14 19:47 |
|
|
Questions on VESC tool by da_rul0r » Wed, 2019-08-14 09:47 |
5 |
by Isi Mon, 2021-04-12 17:34 |
|
|
Get data from VESC on Arduino by jhanvisharma » Wed, 2021-04-07 08:25 |
1 |
by CTSchorsch Wed, 2021-04-07 09:05 |
|
|
VESC failure presumably due to current oscillations at high current by rsarver » Wed, 2021-03-24 22:06 |
0 |
by rsarver Wed, 2021-03-24 22:06 |
|
|
Full Brake vs Switch Off by meisterpro » Mon, 2021-03-22 14:36 |
0 |
by meisterpro Mon, 2021-03-22 14:36 |
|
|
Data logging by charper » Wed, 2019-05-22 00:48 |
4 |
by StvMan Sun, 2021-03-21 17:20 |
|
|
D vs omega control by rsarver » Wed, 2021-03-17 14:44 |
0 |
by rsarver Wed, 2021-03-17 14:44 |
Log in to post new content in the forum.
