You are here

General discussion

Topic / Topic starter Replies Last postsort ascending
Normal topic VESC on DIY CNC router
by tbartoletta » Wed, 2019-02-20 03:00
5
by GunnarW
Thu, 2019-02-21 16:44
Normal topic VESC Questions from the newbie
by mendez » Fri, 2019-02-08 21:13
10
by frank
Mon, 2019-02-18 08:52
Normal topic information to drive 400kv drone motor on ClosedLoop with AS5047
by Syl2078 » Sun, 2019-02-17 19:20
0
by Syl2078
Sun, 2019-02-17 19:20
Normal topic Observer tracking fail
by dangminhducnbk » Sun, 2019-02-17 14:09
0
by dangminhducnbk
Sun, 2019-02-17 14:09
Normal topic Struggling in startup BLDC in sensorless mode
by dangminhducnbk » Fri, 2019-02-15 03:42
2
by dangminhducnbk
Sun, 2019-02-17 12:48
Normal topic 2 vs 3 phase shunts
by antonchromjak » Sun, 2018-04-15 13:25
13
by TechAUmNu
Fri, 2019-02-15 18:57
Normal topic No connection with vesc
by Matthieu van Ra... » Wed, 2019-02-13 18:07
8
by sam.vanratt
Thu, 2019-02-14 15:33
Normal topic Building the vesc firmware in Chibi Studio
by chris1seto » Sat, 2019-01-12 02:36
1
by kinzma
Thu, 2019-02-14 09:42
Normal topic Always get Fault:DRV in FOC mode during startup .
by stone_1706 » Sat, 2019-02-02 17:35
3
by stone_1706
Tue, 2019-02-12 03:20
Normal topic Sub zero temperature VESC412 issues
by jetigm » Fri, 2019-02-08 21:12
3
by sam.vanratt
Sun, 2019-02-10 14:07
Normal topic Dual brushed motors from 1 R/C stick?
by VESC1 » Thu, 2019-01-31 06:19
5
by sam.vanratt
Sun, 2019-02-03 16:30
Normal topic Fault:DRV8302 DUAL V4
by Lzx19961014 » Tue, 2018-09-04 11:48
3
by stone_1706
Sat, 2019-02-02 17:09
Normal topic VESC Tool Instructions
by brschaefer74 » Fri, 2019-01-25 03:49
4
by sam.vanratt
Sat, 2019-01-26 12:52
Normal topic VESC and Motors for sale.
by raess » Thu, 2019-01-24 22:41
0
by raess
Thu, 2019-01-24 22:41
Normal topic Connect both hall and incremental quadrature encoders
by vpl » Tue, 2019-01-15 14:24
1
by galp
Thu, 2019-01-24 14:25
Normal topic Increasing low rpm torque in FOC mode
by galp » Mon, 2019-01-21 18:15
1
by sam.vanratt
Thu, 2019-01-24 00:02
Normal topic Separate Deadband for ADC2?
by striderkent » Wed, 2019-01-23 16:31
0
by striderkent
Wed, 2019-01-23 16:31
Normal topic Angle offset detection
by Gas_Sn4ke » Mon, 2019-01-21 07:09
0
by Gas_Sn4ke
Mon, 2019-01-21 07:09
Normal topic Change RPM of motor
by Gas_Sn4ke » Wed, 2019-01-16 03:51
2
by Shaik Siraaj
Thu, 2019-01-17 11:14
Hot topic Vesc 6 motor setup fault
by Davo69URX » Wed, 2017-11-29 09:22
21
by Tresor
Wed, 2019-01-16 12:38
Normal topic Upload bootloader to new MCU
by Jessica » Fri, 2019-01-11 14:43
7
by Jessica
Wed, 2019-01-16 09:07
Normal topic 4kw BLDC hybrid system help
by thardi10 » Tue, 2019-01-08 17:06
2
by frank
Tue, 2019-01-15 22:15
Normal topic Can not adjust the RPM on my 1350 w motor
by Arne Norway » Wed, 2019-01-09 18:47
6
by sam.vanratt
Sun, 2019-01-13 13:36
Normal topic Dead VESC. Power up when motor is spinning.
by Bor Zabric » Mon, 2018-10-08 10:16
4
by striderkent
Fri, 2019-01-11 18:46
Normal topic VESC acceleration control on setRPM
by fourchette » Tue, 2019-01-08 12:02
3
by fourchette
Wed, 2019-01-09 10:38
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - General discussion