You are here

General discussion

Topic / Topic starter Replies Last postsort ascending
Normal topic How to increase the +/-165A rms current limit to 250A+ rms (350-400A peak)
by ev_motors » Sat, 2018-04-28 10:18
0
by ev_motors
Sat, 2018-04-28 10:18
Normal topic The motor with an enkoder of AS5048 rotates unevenly
by densor » Thu, 2018-04-26 11:41
2
by densor
Fri, 2018-04-27 08:27
Normal topic Dollar signs break private messages
by TechAUmNu » Tue, 2018-04-24 18:09
0
by TechAUmNu
Tue, 2018-04-24 18:09
Normal topic Duty vs RPM for smooth start and slow running
by Davideo » Tue, 2018-04-24 14:42
0
by Davideo
Tue, 2018-04-24 14:42
Normal topic ERPM settings restrict carving speed on outer wheel. Poor user experience.
by Paul15578 » Fri, 2018-01-12 02:28
9
by Ackmaniac
Tue, 2018-04-24 13:47
Normal topic Brakes completely repeatedly failing at high temperature
by Paul15578 » Mon, 2018-03-26 13:06
10
by Paul15578
Sun, 2018-04-22 14:16
Normal topic Firmware update thru UART?
by cromoly » Tue, 2018-04-17 01:19
4
by cromoly
Fri, 2018-04-20 19:22
Normal topic can't reach the maximum speed
by kingpon » Sat, 2017-10-28 04:55
3
by elektrinis
Tue, 2018-04-17 21:50
Normal topic Extending current shunt amplifier voltage
by TechAUmNu » Wed, 2018-04-11 00:43
2
by Roger Wolff
Tue, 2018-04-17 08:56
Hot topic Hall sensor filter on VESC flier board
by raess » Tue, 2018-03-27 21:00
17
by raess
Wed, 2018-04-11 13:43
Normal topic Motor temperature increase
by e-biker » Sun, 2018-04-08 20:17
4
by e-biker
Mon, 2018-04-09 14:44
Normal topic Can't find Configurable FOC current filter in VESC TOOL
by e-biker » Sun, 2018-04-08 12:18
2
by e-biker
Sun, 2018-04-08 12:55
Normal topic Potentiometer control
by khadra.m123 » Thu, 2018-04-05 08:51
3
by slapshot136
Sun, 2018-04-08 00:07
Normal topic acceleration speed and temp noise
by badger1666 » Wed, 2018-04-04 20:18
5
by badger1666
Fri, 2018-04-06 20:13
Normal topic Timeout Brake Current [Fail Save]
by Cuprani » Mon, 2018-04-02 00:03
2
by Cuprani
Tue, 2018-04-03 12:28
Normal topic vesc6 help me learn
by badger1666 » Sat, 2018-03-31 09:05
2
by badger1666
Mon, 2018-04-02 20:15
Normal topic can not start motor with high duty
by qdxiatao » Sat, 2018-03-24 03:58
0
by qdxiatao
Sat, 2018-03-24 03:58
Normal topic Can motor parameters be detected with shaft load?
by powerlabor001 » Thu, 2018-03-15 13:24
4
by powerlabor001
Sat, 2018-03-24 03:07
Normal topic Which encoders are supported?
by raess » Thu, 2018-03-22 23:38
2
by raess
Fri, 2018-03-23 22:58
Normal topic Noise with Hall sensor at high speed
by yosoufe » Thu, 2018-03-08 12:34
9
by yosoufe
Tue, 2018-03-20 09:30
Normal topic Realtime Tachometer readings over UART
by Davideo » Thu, 2017-12-07 00:10
1
by azobe
Mon, 2018-03-19 04:28
Normal topic how to stop regenerative braking option ?
by tauhid.ann » Mon, 2018-03-12 18:40
5
by tauhid.ann
Sat, 2018-03-17 21:21
Normal topic UART GND to Battery (-), good idea ?
by Pimousse » Sat, 2017-09-23 00:47
1
by Dillon
Sat, 2018-03-17 05:56
Normal topic Website updates
by benjamin » Fri, 2018-02-23 17:45
5
by benjamin
Wed, 2018-03-14 10:46
Normal topic FOC Issue
by Davideo » Mon, 2018-02-19 03:30
6
by yosoufe
Thu, 2018-03-08 13:19
New posts
No new posts
Hot topic with new posts
Hot topic without new posts
Sticky topic
Locked topic
Subscribe to RSS - General discussion