You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
VESC Tool Instructions by brschaefer74 » Fri, 2019-01-25 03:49 |
4 |
by sam.vanratt Sat, 2019-01-26 12:52 |
|
|
VESC and Motors for sale. by raess » Thu, 2019-01-24 22:41 |
0 |
by raess Thu, 2019-01-24 22:41 |
|
|
Connect both hall and incremental quadrature encoders by vpl » Tue, 2019-01-15 14:24 |
1 |
by galp Thu, 2019-01-24 14:25 |
|
|
Increasing low rpm torque in FOC mode by galp » Mon, 2019-01-21 18:15 |
1 |
by sam.vanratt Thu, 2019-01-24 00:02 |
|
|
Separate Deadband for ADC2? by striderkent » Wed, 2019-01-23 16:31 |
0 |
by striderkent Wed, 2019-01-23 16:31 |
|
|
Angle offset detection by Gas_Sn4ke » Mon, 2019-01-21 07:09 |
0 |
by Gas_Sn4ke Mon, 2019-01-21 07:09 |
|
|
Change RPM of motor by Gas_Sn4ke » Wed, 2019-01-16 03:51 |
2 |
by Shaik Siraaj Thu, 2019-01-17 11:14 |
|
|
Vesc 6 motor setup fault by Davo69URX » Wed, 2017-11-29 09:22 |
21 |
by Tresor Wed, 2019-01-16 12:38 |
|
|
Upload bootloader to new MCU by Jessica » Fri, 2019-01-11 14:43 |
7 |
by Jessica Wed, 2019-01-16 09:07 |
|
|
4kw BLDC hybrid system help by thardi10 » Tue, 2019-01-08 17:06 |
2 |
by frank Tue, 2019-01-15 22:15 |
|
|
Can not adjust the RPM on my 1350 w motor by Arne Norway » Wed, 2019-01-09 18:47 |
6 |
by sam.vanratt Sun, 2019-01-13 13:36 |
|
|
Dead VESC. Power up when motor is spinning. by Bor Zabric » Mon, 2018-10-08 10:16 |
4 |
by striderkent Fri, 2019-01-11 18:46 |
|
|
VESC acceleration control on setRPM by fourchette » Tue, 2019-01-08 12:02 |
3 |
by fourchette Wed, 2019-01-09 10:38 |
|
|
Fast Startup problem by sam.vanratt » Thu, 2019-01-03 17:56 |
7 |
by sam.vanratt Sun, 2019-01-06 23:25 |
|
|
ADC1 problems with Firmware/Hardware issue? by sam.vanratt » Thu, 2018-12-27 22:31 |
4 |
by sam.vanratt Thu, 2019-01-03 17:46 |
|
|
VESC 4.12 with big-BLDC problem by sam.vanratt » Mon, 2018-12-10 15:59 |
6 |
by sam.vanratt Thu, 2019-01-03 17:44 |
|
|
Cruise function already implemented? by sam.vanratt » Wed, 2019-01-02 17:05 |
0 |
by sam.vanratt Wed, 2019-01-02 17:20 |
|
|
PPM Mislabeled by stevemk14ebr » Fri, 2018-12-21 01:49 |
1 |
by Roger Wolff Tue, 2019-01-01 12:12 |
|
|
Position accuracy by wall0069 » Sat, 2018-12-22 00:25 |
3 |
by sam.vanratt Thu, 2018-12-27 20:39 |
|
|
Bluetooth from vesc to pc issues by TyDaTyga » Wed, 2018-11-28 01:42 |
2 |
by badger1666 Fri, 2018-12-21 17:14 |
|
|
AS5047 over SPI pins on VESC six by Jessica » Fri, 2018-12-21 11:10 |
0 |
by Jessica Fri, 2018-12-21 11:10 |
|
|
vesc6 help with hub motor by badger1666 » Thu, 2018-12-20 18:36 |
4 |
by badger1666 Fri, 2018-12-21 06:03 |
|
|
Sensorless Startup Motor Cogging by Swinde12 » Sun, 2018-12-16 06:12 |
2 |
by Swinde12 Tue, 2018-12-18 19:05 |
|
|
Problems with motor and encoder in PID application by Shaik Siraaj » Thu, 2018-12-13 09:57 |
1 |
by Shaik Siraaj Fri, 2018-12-14 10:14 |
|
|
FOC observer error. by Roger Wolff » Thu, 2018-06-07 13:43 |
4 |
by district9prawn Wed, 2018-12-12 23:44 |
Log in to post new content in the forum.
