You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Sensorless Startup Motor Cogging by Swinde12 » Sun, 2018-12-16 06:12 |
2 |
by Swinde12 Tue, 2018-12-18 19:05 |
|
|
Problems with motor and encoder in PID application by Shaik Siraaj » Thu, 2018-12-13 09:57 |
1 |
by Shaik Siraaj Fri, 2018-12-14 10:14 |
|
|
FOC observer error. by Roger Wolff » Thu, 2018-06-07 13:43 |
4 |
by district9prawn Wed, 2018-12-12 23:44 |
|
|
VESC75/300 pre-order, limited volume by frank » Fri, 2018-11-23 10:06 |
11 |
by benjamin Mon, 2018-12-10 08:19 |
|
|
Boat indexed throttle - how to connect and what resistance by trolling » Sat, 2018-12-08 19:45 |
0 |
by trolling Sat, 2018-12-08 19:45 |
|
|
Melting issues in FOC (VESC4.2) by e-nduro » Mon, 2018-12-03 21:51 |
1 |
by e-nduro Fri, 2018-12-07 23:38 |
|
|
Problem with encoder readings with arduino by ruthvikchanda » Thu, 2018-12-06 07:06 |
0 |
by ruthvikchanda Thu, 2018-12-06 10:23 |
|
|
Sound when braking and Accelerating by Paul15578 » Wed, 2018-01-03 10:04 |
11 |
by frank Thu, 2018-12-06 10:22 |
|
|
problem with encoder readings for proper feedback using arduino by ruthvikchanda » Thu, 2018-12-06 07:05 |
0 |
by ruthvikchanda Thu, 2018-12-06 07:05 |
|
|
Lawn mower by charper » Mon, 2018-12-03 14:25 |
0 |
by charper Mon, 2018-12-03 14:25 |
|
|
vesc <-> arduino micro troubleshooting UART issues by fourchette » Mon, 2018-11-26 11:59 |
1 |
by fourchette Mon, 2018-12-03 13:41 |
|
|
Fried C51(?) on my VESC 4.12 by spork » Tue, 2018-11-27 07:00 |
6 |
by spork Thu, 2018-11-29 16:43 |
|
|
Stall torque in sensorless mode by cromoly » Sun, 2018-11-25 07:54 |
4 |
by spork Thu, 2018-11-29 03:23 |
|
|
Using reverse with a spare channel by spork » Mon, 2018-11-26 07:08 |
4 |
by spork Tue, 2018-11-27 06:48 |
|
|
Duty cycle-what does that control? by cromoly » Sat, 2018-11-24 01:11 |
2 |
by cromoly Sun, 2018-11-25 07:40 |
|
|
HArd power off switch by jakaranda » Mon, 2018-10-29 11:15 |
3 |
by sam.vanratt Sat, 2018-11-24 18:08 |
|
|
USB can not recognize by xiaofeixiak » Sat, 2018-11-24 03:20 |
1 |
by sam.vanratt Sat, 2018-11-24 14:44 |
|
|
Encoder over SPI doesn't work on FW3.40: SOLVED by john » Mon, 2018-11-12 09:00 |
2 |
by john Fri, 2018-11-23 16:40 |
|
|
LED HW PWM?? by milom » Fri, 2018-11-16 15:29 |
1 |
by benjamin Fri, 2018-11-23 09:57 |
|
|
Fried Hall Effect Throttle Sensor by cdw3423vesc » Thu, 2018-11-15 05:16 |
2 |
by sam.vanratt Thu, 2018-11-22 20:33 |
|
|
VESC TOOL ADC Voltage mapping too low. SOLVED by Ecyclist » Fri, 2018-10-19 22:38 |
5 |
by sam.vanratt Thu, 2018-11-22 20:21 |
|
|
Noise between VESC and microcontroller by onsokumaru » Tue, 2018-04-03 21:56 |
2 |
by fourchette Tue, 2018-11-20 21:32 |
|
|
enertionboard focbox : is vesc_tool safe to use? by fourchette » Wed, 2018-11-07 23:49 |
4 |
by fourchette Tue, 2018-11-20 21:13 |
|
|
where to source BLDC 6.5in geared wheel? by fourchette » Thu, 2018-11-08 00:05 |
3 |
by fourchette Mon, 2018-11-19 22:54 |
|
|
Best way to stop "de-sync" of motors by Paul15578 » Tue, 2017-12-05 04:57 |
11 |
by Dillon Mon, 2018-11-19 02:11 |
Log in to post new content in the forum.
