You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
Is electronic brake always REGEN? by Tilman Baumann » Tue, 2018-04-10 11:16 |
19 |
by henxan Sun, 2019-11-17 18:30 |
|
|
a motor for VESC !! by themotorman » Sat, 2018-12-29 06:19 |
5 |
by TechAUmNu Fri, 2019-11-15 14:20 |
|
|
Vesc gps control by Erik » Thu, 2019-11-14 20:38 |
0 |
by Erik Thu, 2019-11-14 20:38 |
|
|
Vesc WS2812b led issues & support by Ash » Tue, 2019-11-12 08:40 |
0 |
by Ash Tue, 2019-11-12 14:13 |
|
|
75/300 connection issues FW3.6 by renaudbarbier » Fri, 2019-11-01 20:17 |
3 |
by frank Tue, 2019-11-05 09:18 |
|
|
75/300 Large inrunner problem (video) by dk-odense » Mon, 2019-11-04 21:53 |
1 |
by frank Tue, 2019-11-05 09:06 |
|
|
Electric moped self build. by Moped Mickey » Mon, 2019-10-28 18:15 |
1 |
by frank Mon, 2019-11-04 13:39 |
|
|
USB Unable to connect by Bazeljet » Thu, 2019-10-10 06:02 |
5 |
by portnawake Mon, 2019-10-28 21:42 |
|
|
VESC 75/300 + ~20kW motor , bms configuration problem... by gucho » Sat, 2019-10-26 14:45 |
4 |
by hockinsk Mon, 2019-10-28 21:33 |
|
|
Using the parameter editor by dqt boi » Thu, 2019-10-24 23:31 |
0 |
by dqt boi Thu, 2019-10-24 23:31 |
|
|
Any issues with the DRV8323? by shaman » Thu, 2019-10-24 21:50 |
0 |
by shaman Thu, 2019-10-24 21:50 |
|
|
VESC - Motor will not start until a small kick is applied from a full stop despite using hall sensors by 010203040506070809 » Wed, 2019-10-23 23:12 |
0 |
by 010203040506070809 Wed, 2019-10-23 23:12 |
|
|
Pulling fault codes without USB by shaman » Fri, 2019-10-18 15:13 |
5 |
by shaman Sun, 2019-10-20 22:54 |
|
|
VESC as a 3 phase inverter to power a grid model by pf26 » Tue, 2019-03-19 20:54 |
5 |
by shaman Fri, 2019-10-18 15:06 |
|
|
New to electronics, I have some questions about monitoring RPM by Trent » Fri, 2019-10-18 08:01 |
1 |
by frank Fri, 2019-10-18 13:34 |
|
|
Much lower torque in foc compared to bldc mode by asaf123098 » Sat, 2019-10-12 18:26 |
1 |
by frank Thu, 2019-10-17 11:15 |
|
|
GPDrive as AC current source by jdn2 » Tue, 2019-10-15 14:22 |
1 |
by frank Thu, 2019-10-17 11:14 |
|
|
Connecting the VESC6 plus with servo wires by GreenPenguin » Wed, 2019-10-16 15:39 |
1 |
by frank Thu, 2019-10-17 11:11 |
|
|
Vesc 6 U11 part number by ems23 » Wed, 2019-10-02 17:16 |
1 |
by benjamin Tue, 2019-10-15 11:46 |
|
|
Why switchable current filters? by BillyJ » Sat, 2019-10-05 12:22 |
2 |
by shaman Sun, 2019-10-13 17:41 |
|
|
Wand Cruise Control, and speed control only working on Master VESC by MaddiQ » Mon, 2019-09-16 20:46 |
15 |
by hans_maier Fri, 2019-10-11 00:22 |
|
|
BLDC Motor Power limitation by tecnico.solarboat » Tue, 2019-10-01 23:42 |
4 |
by tecnico.solarboat Thu, 2019-10-10 15:13 |
|
|
Second uart? by Kubbur » Mon, 2019-09-16 19:32 |
2 |
by benjamin Thu, 2019-10-10 07:34 |
|
|
Does a wireless passive on/off ignition switch that holds its state exist? Need help for my custom electric scooter! by 010203040506070809 » Mon, 2019-09-30 23:59 |
1 |
by Enak Thu, 2019-10-10 03:21 |
|
|
Hall sensors signals tolerance by Pimousse » Tue, 2019-09-17 13:55 |
4 |
by e-biker Wed, 2019-10-09 12:40 |
Log in to post new content in the forum.
