You are here
General discussion
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
SK3 Turnigy 6374 149 / encoder CUI AMT102 => can VESC 4 support position control? by fourchette » Tue, 2019-04-02 23:14 |
5 |
by pf26 Thu, 2019-04-04 11:43 |
|
|
Battlebot Weapon : Trouble spinning up by satacoy » Thu, 2019-04-04 07:29 |
0 |
by satacoy Thu, 2019-04-04 07:29 |
|
|
Current control and duty cycle issues. by ESCam » Tue, 2019-04-02 22:55 |
0 |
by ESCam Tue, 2019-04-02 22:55 |
|
|
Braking in speed PID controlled mode by vadimz » Sat, 2018-09-15 14:19 |
9 |
by zybyxutese Mon, 2019-04-01 13:35 |
|
|
no speed feedback in DC mode by Jessica » Mon, 2018-11-19 11:17 |
6 |
by abrac Sat, 2019-03-30 19:11 |
|
|
STM32F407 by john » Wed, 2019-03-27 13:40 |
0 |
by john Wed, 2019-03-27 13:40 |
|
|
E vehicle setup by jordanlow » Wed, 2019-03-20 10:33 |
4 |
by jordanlow Wed, 2019-03-20 16:18 |
|
|
Master Slave Controller for Motor by Blemot » Tue, 2019-03-19 09:46 |
0 |
by Blemot Tue, 2019-03-19 09:46 |
|
|
VESC 6 DC motor Current limit? by ShortCircuit » Thu, 2019-02-07 21:56 |
14 |
by ShortCircuit Thu, 2019-03-14 19:34 |
|
|
Guide for modifying firmware/ apps by Enak » Wed, 2017-09-06 17:24 |
3 |
by TechAUmNu Thu, 2019-03-14 17:38 |
|
|
DRV8323 by Jessica » Thu, 2019-03-14 11:41 |
0 |
by Jessica Thu, 2019-03-14 11:42 |
|
|
Can I change control mode on the fly through the UART port? by spork » Wed, 2019-03-13 02:24 |
2 |
by spork Wed, 2019-03-13 15:41 |
|
|
Fault finding on failed VESC This topic has been moved to "Third Party Hardware" (View topic) |
|||
|
Input Setup Wizard Does Not Ask if Single or Multi VESC by kylemuramatsu » Wed, 2019-03-13 03:22 |
1 |
by benjamin Wed, 2019-03-13 09:38 |
|
|
how do you arm your Vesc in arduino code? by the creator » Wed, 2019-03-13 01:11 |
0 |
by the creator Wed, 2019-03-13 01:33 |
|
|
ADC pin voltage not zero by zoppp » Fri, 2019-02-08 23:44 |
12 |
by zoppp Tue, 2019-03-12 01:17 |
|
|
VESC regenerating while RPM increased by olivierskypullc... » Fri, 2019-03-08 16:32 |
2 |
by olivierskypullc... Mon, 2019-03-11 10:45 |
|
|
C80100 Outrunner 50kv does not want to spin. by Wormsnake » Sun, 2019-03-03 10:30 |
1 |
by TheFallen Sun, 2019-03-10 17:54 |
|
|
Pedelec/eBike, PAS and sensors by sam.vanratt » Mon, 2018-11-19 11:46 |
2 |
by sam.vanratt Thu, 2019-03-07 20:22 |
|
|
VESC6 PCB questions by ESCam » Sat, 2018-12-29 00:17 |
6 |
by TechAUmNu Thu, 2019-03-07 11:28 |
|
|
Brushless or brushed motor for autonomous rc-car by Joe_Lowtech » Thu, 2018-12-20 11:56 |
4 |
by Joe_Lowtech Tue, 2019-03-05 11:00 |
|
|
Win10 BLE Error by jzy1115 » Tue, 2018-04-17 16:20 |
1 |
by spei Mon, 2019-03-04 13:55 |
|
|
When I mount the propeller on the motor ,I get a new promblem by moto_guy » Sat, 2019-03-02 05:16 |
0 |
by moto_guy Sat, 2019-03-02 05:16 |
|
|
Flipsky6.6 usb not detected This topic has been moved to "Third Party Hardware" (View topic) |
|||
|
BLDC vs FOC mode， motor‘s spin direction is invert by moto_guy » Wed, 2019-02-20 11:48 |
4 |
by moto_guy Sun, 2019-02-24 09:11 |
|
Log in to post new content in the forum.
