hi fellow skaters
i would like to share my issue with logging on vesc tool mobile (sg note 9 android 10)
this is diy build finished few days ago, i had chance to test it each day for about 40min's run and it works great except position logging. i am not sure what is wrong but ill try to explain (ss provided also).
Hey guys,
I am struggling to set up my first vesc. I have the Maytech v4.12. I have it plugged in to my motor, battery and remote. When I go to connect it to my computer this screen pops up
So i try to update the firmware which gives me this message
When I press yes it starts and after about 10 seconds I get this error message
So I've just been working on the motor drivers and I did my first serious speed and power tests using the mobile vesc tool app, and I've been using it and its been really helpful with speed and power limiting and it goes plenty fast downhill and on flat ground, but as soon as I go uphill, the voltage drops really low, which understand is normal, but I don't know what kind of settings I should have to counter this, below are my significant settings
Setup 10S2P 4AH Battery Meepo V3 Battery Li-ion, 2x 540 watt hub motors, 2FSESC 4.20 Pluses
Hi, I was write small Python binding for communicate with device using serial port.
As start point I use yours project. Currently I successfully handle COMM_FW_VERSION:
VESC Firmware Version 3.65, Hardware: 60, UUID: 25 00 2e 00 17 47 37 33 38 33 32 38
Now I parse COMM_GET_IMU_DATA and I have next questions:
1. Can you please explain, what mean byte before CRC value?
Hi there,
My motor runs well during auto detection phases (both FOC and BLDC). After that, the manual controls (D,I,RPM, etc.) don't get it close as smooth. In fact, it only runs at 21% Duty Cycle. Tried PPM input in any available option, still no chance.
I wonder if I can run the detection algorithms inside the tool. Maybe in the development area? Is there some documentation about that?
Eagerly looking to any ideas!
Thanks!
Can anyone explain which pin is used in the auxiliary output mode feature under the advanced tab of the general motor settings? I have use for its functionality.
Hi,
I updated to the latest fw but when I try to run the input wizard, I'm always asked to update the fw to a newer version.
Here are the screenshots to the input wizard message dialog and the current firmware information:
https://www.dropbox.com/s/ljg5o79ljqrubkx/firmware_widget.png?dl=0
https://www.dropbox.com/s/8s04nsldrzcr2va/input_setup_wizard.png?dl=0
Hey Guys
I recently embarked on my first DIY board and with that, my first experience with the VESC tool. Please excuse my ignorance or lack of understanding of any aspects.
Bought a Flipsky6.6 Dual (i know, i probably should have spent the extra and just got a proper VESC) and set up using the VESC tool, paid for and downloaded from here.
Initially went through all the standard initial setup wizards as shown in the documentation here, as well as YouTube videos.
The motors simply don't seem to operate properly.
Hello,
I purchased VESC Tool at 2020-01-01 (Silver) and according to its change log it is version 1.29.
Every time I start it, a windows occures and tells me a newer version would be available and I schould use it. How to get an update?
Gruß, Günter
Hi everyone!
I have downloaded the latest Vesc Tool 2.2 and I'm having problems when flashing a new firmware
My Vesc is a dual Flipsky 4.20 which is basically two 4.12 (4.10) VESCs on a single PCB paired via internal CAN
I used the Ackmaniac's vesc tool previously with the FW version 3.103.
I connected the VESC via USB, disabled the can forwarding and tried to update the single side only.
The RT data is disabled.
I get the following errors in the debug console
