You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
Help setting up a segway in hub motor wheel by tonycowan on Mon, 2021-08-30 19:39 |
2 |
by Pakran Sun, 2021-09-19 15:02 |
General discussion | |
VESC FOC EFFICIENCY vs. REGULAR BLDC ESC (Fixed Wing UAV Propeller Tests) by drummerboy5408 on Sat, 2021-09-18 05:04 |
2 |
by drummerboy5408 Sun, 2021-09-19 07:09 |
General discussion | |
Encoder support in BLDC by dirkvl on Sat, 2021-09-18 12:21 |
by dirkvl Sat, 2021-09-18 12:21 |
Feature Requests | ||
BEFM (direct drive motor) higher than battery voltage. by BalorNG on Fri, 2021-04-02 18:04 |
1 |
by skyline1970 Sat, 2021-09-18 12:05 |
General discussion | |
Reverse direction by ISanberg on Sun, 2021-03-28 22:22 |
1 |
by skyline1970 Sat, 2021-09-18 12:01 |
General discussion | |
3 Phase DC Motor and VESC by Mustard on Sun, 2021-05-23 19:03 |
1 |
by skyline1970 Sat, 2021-09-18 11:50 |
General discussion | |
Battery/Motor Current on VESC Tool is less than Actuals by gowrav on Thu, 2021-07-15 13:27 |
1 |
by skyline1970 Sat, 2021-09-18 11:44 |
General discussion | |
ADC Brake while stand , not parking brake by spacewalker on Tue, 2021-07-27 08:09 |
1 |
by skyline1970 Sat, 2021-09-18 11:42 |
General discussion | |
4.12 Hardware without drv chip by Gatze on Thu, 2021-08-26 11:13 |
1 |
by skyline1970 Sat, 2021-09-18 11:32 |
Third Party Hardware | |
command in power by Flyingtux on Thu, 2021-08-26 18:00 |
1 |
by skyline1970 Sat, 2021-09-18 11:31 |
General discussion | |
Powertool switch on VESC by Toto on Mon, 2021-09-13 12:06 |
1 |
by skyline1970 Sat, 2021-09-18 11:25 |
General discussion | |
tuning PID speed for the skateboard motor with hall sensors by salviador on Tue, 2021-09-14 14:37 |
1 |
by skyline1970 Sat, 2021-09-18 11:18 |
General discussion | |
Encoder Index Interrupt Code by dylanm on Sat, 2021-09-18 00:05 |
by dylanm Sat, 2021-09-18 00:05 |
VESC Firmware | ||
Flipsky Dual FSESC6.6 loses connection, connected BLDC buzzing after restart by gabrielredding on Mon, 2019-04-29 00:00 |
3 |
by Constantin00 Fri, 2021-09-17 11:00 |
Third Party Hardware | |
motor stuttering and having a hard time with receiver ... help by okyuubix on Tue, 2021-09-14 23:43 |
by okyuubix Tue, 2021-09-14 23:49 |
General discussion | ||
PPM Mapping by russell.morris1... on Tue, 2021-09-14 22:38 |
by russell.morris1... Tue, 2021-09-14 22:38 |
VESC Tool | ||
Can´t increase current by increase RPM by hubacek000 on Mon, 2021-09-13 13:22 |
1 |
by frank Tue, 2021-09-14 12:17 |
VESC Tool | |
How do you wire one power-on push button to two VESC 6 MIIIs? by adamchicago on Mon, 2020-01-20 23:01 |
3 |
by tsharma Tue, 2021-09-14 10:14 |
General discussion | |
Issues flashing VESC HW 4.12 by Nic_cfar on Wed, 2020-10-21 00:08 |
1 |
by xeniter Mon, 2021-09-13 22:33 |
Third Party Hardware | |
Stokemonkey hub motor current draw at rest by SheffyP on Sat, 2021-09-11 14:32 |
2 |
by SheffyP Sun, 2021-09-12 17:44 |
General discussion |