You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
VESC 6 MK IV circuit question by Simmo1337 on Tue, 2022-08-16 23:10 |
by Simmo1337 Tue, 2022-08-16 23:10 |
VESC Original Hardware | ||
|
Spam (Page: 1, 2)
by Davideo on Mon, 2017-12-25 20:49 |
81 |
by canoeman Tue, 2022-08-16 15:19 |
General discussion | |
|
UART for NRF51822 on "old" nrf pins ? by CTSchorsch on Fri, 2019-11-29 16:41 |
6 |
by hl0dk0 Tue, 2022-08-16 12:46 |
Feature Requests | |
|
Small inrunner HFI set-up issue by anthony_ on Thu, 2022-08-11 13:43 |
2 |
by anthony_ Mon, 2022-08-15 13:45 |
General discussion | |
|
Bafang BBSHD hub motor setup by csev-tcejorp on Sat, 2022-08-13 14:50 |
by csev-tcejorp Sat, 2022-08-13 14:50 |
Feature Requests | ||
|
Vesc 100/250 for unsensored brushless motors by jmurba on Fri, 2022-08-05 12:05 |
3 |
by velolac Fri, 2022-08-12 22:14 |
General discussion | |
|
[SOLVED] VESC75/300 Poor Performance when Cold by canoeman on Tue, 2022-01-25 23:46 |
25 |
by canoeman Fri, 2022-08-12 19:13 |
VESC Original Hardware | |
|
VESC & CAN Bus Communication to another MCU (NOT VESC) by Jack_Li on Thu, 2019-07-11 04:08 |
5 |
by David_1 Thu, 2022-08-11 22:08 |
VESC Firmware | |
|
step/dir by blueflower on Thu, 2020-01-16 04:15 |
5 |
by akkoxe Mon, 2022-08-08 06:34 |
General discussion | |
|
KV command in terminal ( how to determine kv of a motor ) by fessyfoo on Sat, 2020-05-09 21:21 |
1 |
by rafeh1 Mon, 2022-08-08 04:31 |
VESC Tool | |
|
Flipsky 75100 with Flipsky VX1 remote -- do I have the wiring right? (VESC4 connector) by SeguinM on Sun, 2022-08-07 15:32 |
by SeguinM Sun, 2022-08-07 15:32 |
Third Party Hardware | ||
|
iq sign reversal at high RPM (was: Duty cycle jumps to maximum when *lowering* current limit) by vadimz on Thu, 2022-06-23 14:00 |
4 |
by vadimz Sun, 2022-08-07 13:03 |
VESC Firmware | |
|
Tips on tuning PID for a 170mm RW170 hub motor, 15 pole-pairs, low speed, high torque, 0-3000 ERPM by PaulMakesThings on Fri, 2022-08-05 11:06 |
by PaulMakesThings Fri, 2022-08-05 11:06 |
General discussion | ||
|
temperature compensation make sense？ by alexshen2012 on Thu, 2022-08-04 08:28 |
1 |
by alexshen2012 Thu, 2022-08-04 09:17 |
General discussion | |
|
FAULT_CODE_UNDER_VOLTAGE by alexantosh on Mon, 2021-11-29 09:26 |
9 |
by heravinluca Thu, 2022-08-04 04:19 |
VESC Tool | |
|
VESC Setup - Fluctuating/Unstable Duty Cycle/eRPM/Current by liminalsunset on Thu, 2022-08-04 01:44 |
by liminalsunset Thu, 2022-08-04 01:44 |
General discussion | ||
|
Different rpm when using 3 vesc with can-bus by ewakegermanyhq on Wed, 2022-08-03 17:03 |
by ewakegermanyhq Wed, 2022-08-03 17:03 |
VESC Tool | ||
|
Lanyard kill switch by craig w on Mon, 2022-01-03 09:30 |
3 |
by ewakegermanyhq Wed, 2022-08-03 16:55 |
General discussion | |
|
Under rated VESC for motor, problem? by Alistair Goodman on Wed, 2022-08-03 12:53 |
2 |
by Alistair Goodman Wed, 2022-08-03 15:27 |
General discussion | |
|
VESC BMS Hardware Reference Design by DubP on Fri, 2021-09-03 21:00 |
10 |
by frank Wed, 2022-08-03 14:34 |
VESC Original Hardware |
Pages
