You are here
Active forum topics
Primary tabs
Topic | Replies | Last post | Forum | |
---|---|---|---|---|
bldc motor detection with Focbox and 190kv motor by gicho on Mon, 2018-01-15 23:04 |
1 |
by linsus Wed, 2018-01-17 10:23 |
General discussion | |
3 Phase DC Motor and VESC by Mustard on Sun, 2021-05-23 19:03 |
1 |
by skyline1970 Sat, 2021-09-18 11:50 |
General discussion | |
Connect VESC4.7 over USB by Lars_Dierickx on Thu, 2023-03-09 16:13 |
1 |
by Jou2023 Mon, 2023-05-29 11:13 |
VESC Tool | |
VESC Blink codes by ligi on Wed, 2022-03-16 12:36 |
1 |
by frank Wed, 2022-03-16 14:57 |
General discussion | |
VESC Firmware update not working by timhermanson94 on Wed, 2019-07-31 18:42 |
1 |
by skyline1970 Fri, 2019-08-02 15:22 |
VESC Firmware | |
FSESC 4.12 oscillating and making noise by hichemhlm on Sun, 2020-03-29 13:33 |
1 |
by hichemhlm Sun, 2020-12-27 12:19 |
General discussion | |
Gate driver by RSR on Sat, 2019-01-26 21:46 |
1 |
by bgdwiepp Fri, 2019-03-01 15:21 |
Third Party Hardware | |
Building the vesc firmware in Chibi Studio by chris1seto on Sat, 2019-01-12 02:36 |
1 |
by kinzma Thu, 2019-02-14 09:42 |
General discussion | |
I can't communicate with the VESC-Clone by Savavit on Sun, 2019-10-27 17:42 |
1 |
by vadicus Thu, 2019-11-07 06:48 |
Third Party Hardware | |
Balancing Throttle by kstuck on Mon, 2022-12-12 22:31 |
1 |
by frank Tue, 2022-12-13 10:37 |
General discussion | |
Connecting VESC to XAVIER by MrMonk3y on Wed, 2019-05-01 09:53 |
1 |
by MrMonk3y Wed, 2019-05-08 13:34 |
General discussion | |
Driving two motors with 75/300 by cmarc on Wed, 2019-10-16 17:32 |
1 |
by benjamin Fri, 2019-10-18 10:37 |
VESC Original Hardware | |
Flipsky ADC always high by Bariiq on Fri, 2019-04-19 11:46 |
1 |
by andrecorreia Fri, 2021-04-30 01:22 |
Third Party Hardware | |
FOC Calibration over CAN by thisisjaye on Fri, 2018-10-26 13:15 |
1 |
by frank Fri, 2018-10-26 17:12 |
General discussion | |
FSESC 6.6 200A Unable to send signal to slave VESC by bms368 on Sat, 2021-02-20 06:16 |
1 |
by adidasgoogle Sun, 2021-03-07 19:11 |
VESC Tool | |
Tuning prop loads with rapid erpm increase in duty cycle or speed control by mirage98 on Mon, 2022-09-26 01:51 |
1 |
by drummerboy5408 Mon, 2022-10-24 05:49 |
General discussion | |
Older VESC BLDC Firmware Version Source Code by Vikram Bhat on Mon, 2022-09-12 03:16 |
1 |
by frank Tue, 2022-09-13 21:09 |
VESC Firmware | |
3 shunt low side resistor configuration based on VESC 6 by jordanlow on Thu, 2019-02-14 16:42 |
1 |
by TechAUmNu Thu, 2019-02-14 18:31 |
Third Party Hardware | |
How to access VESC error codes in the new VESC tool by berno3 on Tue, 2018-06-05 08:47 |
1 |
by Roger Wolff Wed, 2018-06-06 07:36 |
VESC Tool | |
Step-by-step manual or overview for VESC + Arduino control by vretier on Sat, 2021-11-20 21:39 |
1 |
by skyline1970 Sun, 2021-11-21 08:33 |
General discussion |