You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Motor runs only at constant speed (with VESC 100V200A and Flipsky VX3). by Tom65 on Wed, 2023-04-12 16:28 |
by Tom65 Wed, 2023-04-12 16:28 |
General discussion | ||
|
Hi by elsie on Thu, 2018-01-25 02:49 |
by elsie Thu, 2018-01-25 16:23 |
General discussion | ||
|
Combat Robot Mods by BrianNave on Sun, 2019-02-24 17:03 |
by BrianNave Sun, 2019-02-24 17:03 |
Feature Requests | ||
|
Check 3rd party firmware *.bin file by etienne on Mon, 2022-09-26 15:31 |
by etienne Mon, 2022-09-26 15:31 |
VESC Firmware | ||
|
can not start motor with high duty by qdxiatao on Sat, 2018-03-24 03:58 |
by qdxiatao Sat, 2018-03-24 03:58 |
General discussion | ||
|
VESC - Motor will not start until a small kick is applied from a full stop despite using hall sensors by 010203040506070809 on Wed, 2019-10-23 23:12 |
by 010203040506070809 Wed, 2019-10-23 23:12 |
General discussion | ||
|
vesc tool not giving me the right values by spacemango on Tue, 2020-06-09 13:31 |
by spacemango Tue, 2020-06-09 13:42 |
General discussion | ||
|
mcpwm_foc and mcpwm tutorial by nami1216 on Tue, 2019-10-15 07:12 |
by nami1216 Tue, 2019-10-15 07:12 |
VESC Firmware | ||
|
How to reboot VESC from serial port by Ivko on Mon, 2021-01-04 18:44 |
by Ivko Mon, 2021-01-04 18:44 |
General discussion | ||
|
Where can I ask technical questions about products? by MrSurly on Tue, 2022-04-19 05:22 |
by MrSurly Tue, 2022-04-19 05:22 |
General discussion | ||
|
Choosing Motor Encoder for VESC by VRdublove on Fri, 2020-01-24 18:51 |
by VRdublove Fri, 2020-01-24 21:44 |
VESC Original Hardware | ||
|
current control mode with duty cycle limit based on throttle by devin on Thu, 2020-01-16 05:45 |
by devin Thu, 2020-01-16 05:49 |
General discussion | ||
|
motor output voltage vs input voltage by rsarver on Wed, 2021-03-17 15:55 |
by rsarver Wed, 2021-03-17 15:55 |
General discussion | ||
|
Lawn mower by charper on Mon, 2018-12-03 14:25 |
by charper Mon, 2018-12-03 14:25 |
General discussion | ||
|
Difference between regular and 'setup' values in logged csv by aUser on Tue, 2024-04-23 14:03 |
by aUser Tue, 2024-04-23 14:03 |
VESC Tool | ||
|
[solved] Firmware 5.01 gcc compile fail.. need some insight by Bill Somerville on Tue, 2020-11-03 19:44 |
by Bill Somerville Fri, 2020-11-06 23:20 |
VESC Firmware | ||
|
Terminal Command for Current? by Mannerow on Thu, 2020-10-29 23:07 |
by Mannerow Thu, 2020-10-29 23:07 |
VESC Tool | ||
|
Direct drive wheel ac servo+vesc by adilrepas on Wed, 2021-05-26 12:50 |
by adilrepas Wed, 2021-05-26 12:58 |
General discussion | ||
|
Request Feature to add minimum Battery Voltage value in addition to duty cycle for field weakening by aquaponiccowboy on Mon, 2022-10-17 04:49 |
by aquaponiccowboy Mon, 2022-10-17 04:50 |
Feature Requests | ||
|
how to communication with arduino on vesc via CAN by yuri12 on Tue, 2022-02-08 13:16 |
by yuri12 Tue, 2022-02-08 13:16 |
VESC Tool |
Pages
