You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
step by step ebike thorttle setup by sindre on Wed, 2019-07-03 17:59 |
by sindre Wed, 2019-07-03 17:59 |
General discussion | ||
|
CAN Bus Control by External Host by josh on Fri, 2018-11-30 06:43 |
3 |
by Jack_Li Mon, 2019-07-01 10:37 |
General discussion | |
|
VESC 6.0 Data Logging? by josh on Fri, 2017-06-30 00:00 |
11 |
by e-nduro Sun, 2019-06-30 22:35 |
VESC6 Beta | |
|
5V/serial weirdness when using FOC by wihrl on Sat, 2019-06-15 12:57 |
1 |
by frank Fri, 2019-06-28 14:13 |
General discussion | |
|
Low duty cycle issues by nathantarlinton on Tue, 2019-06-25 03:01 |
1 |
by bobfrank Tue, 2019-06-25 03:39 |
General discussion | |
|
Motor spins only with outside help by asaf123098 on Thu, 2019-04-04 06:52 |
4 |
by dekafive Thu, 2019-06-20 11:36 |
Third Party Hardware | |
|
Problem to start bldc in vesc tool vesc-mini4 esc by uav-orion on Wed, 2019-06-12 16:18 |
5 |
by uav-orion Wed, 2019-06-19 21:50 |
General discussion | |
|
dual VESC battery current by chris_winkel on Tue, 2019-06-18 15:26 |
by chris_winkel Tue, 2019-06-18 15:26 |
VESC Original Hardware | ||
|
order from Trampa boards by Abricosvw on Mon, 2019-06-17 02:06 |
1 |
by frank Mon, 2019-06-17 17:01 |
General discussion | |
|
Regenerative braking question and vesc input question by asaf123098 on Sat, 2019-06-15 09:55 |
2 |
by asaf123098 Sun, 2019-06-16 00:23 |
General discussion | |
|
Difference between maximum current values by Rico on Fri, 2019-06-14 16:06 |
1 |
by frank Sat, 2019-06-15 12:21 |
General discussion | |
|
Motor refuses to spin after Wizard, VESC 6.6 by Wisdomwagon on Thu, 2019-06-13 16:20 |
1 |
by Wisdomwagon Thu, 2019-06-13 18:54 |
General discussion | |
|
Recommended way to implement CAN-bus communication using a Linux based controller by toma on Tue, 2019-06-11 08:32 |
8 |
by toma Thu, 2019-06-13 07:43 |
General discussion | |
|
VESC 6 FOC wizard and current limitations. by Bor Zabric on Mon, 2019-06-10 21:12 |
1 |
by TechAUmNu Wed, 2019-06-12 14:42 |
General discussion | |
|
VESC not responding to Controller by jcab on Thu, 2018-03-08 21:51 |
4 |
by Popeye Mon, 2019-06-10 23:59 |
VESC Firmware | |
|
Sync loss when switching from HALL to sensorless by blezalex on Fri, 2019-05-24 19:00 |
1 |
by blezalex Mon, 2019-06-10 23:26 |
General discussion | |
|
Step/Dir signals by wall0069 on Sun, 2019-06-09 16:06 |
by wall0069 Sun, 2019-06-09 16:06 |
General discussion | ||
|
Brake Current Command Adjustments by josh on Fri, 2019-05-17 21:37 |
2 |
by josh Wed, 2019-06-05 17:14 |
General discussion | |
|
How exactly do I connect a VESC 6.4 to an Arduino Nano? by MaxMaker1 on Tue, 2018-07-03 23:18 |
5 |
by molak Tue, 2019-06-04 19:39 |
VESC Original Hardware | |
|
VESC at very low speeds by LudoJ on Wed, 2019-05-15 16:09 |
1 |
by Roger Wolff Sun, 2019-06-02 10:25 |
General discussion |
Pages
