You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 on Fri, 2020-04-10 12:33 |
by olaf2273 Mon, 2020-04-27 15:34 |
General discussion | ||
|
How to set dead time on BLDC mode? by AllenFF on Wed, 2020-04-15 03:30 |
by AllenFF Mon, 2020-04-27 15:34 |
General discussion | ||
|
VESC for EU pedelecs by bb67 on Mon, 2020-04-27 14:11 |
by bb67 Mon, 2020-04-27 14:13 |
General discussion | ||
|
Battery charging using motor inductance by eptv on Sun, 2020-04-26 07:44 |
by eptv Sun, 2020-04-26 07:44 |
General discussion | ||
|
Steering channel (dual vesc setup via CAN bus) by fender90 on Sun, 2020-04-26 03:47 |
by fender90 Sun, 2020-04-26 03:47 |
Feature Requests | ||
|
Nrf connection error by vufmihai on Sat, 2020-04-25 22:00 |
by vufmihai Sat, 2020-04-25 22:00 |
VESC Tool | ||
|
(solved) Configuration smooth motordirection change by horak2084 on Mon, 2019-02-25 20:44 |
9 |
by fpagac Sat, 2020-04-25 17:17 |
VESC Firmware | |
|
Distance based on Phone GPS by Mikko Valtonen on Sat, 2020-04-25 08:33 |
by Mikko Valtonen Sat, 2020-04-25 08:38 |
Feature Requests | ||
|
Smoked 3 month old VESC - What did I do wrong? by cjjohnson97 on Tue, 2020-04-21 17:40 |
3 |
by cjjohnson97 Fri, 2020-04-24 21:38 |
General discussion | |
|
vesc hardware 4.12 by BasilBrushy on Fri, 2020-04-24 11:56 |
by BasilBrushy Fri, 2020-04-24 11:56 |
Third Party Hardware | ||
|
Question about COMM_GET_IMU_DATA packet by rrzaripov on Wed, 2020-03-04 00:28 |
3 |
by Addy Fri, 2020-04-24 06:49 |
VESC Tool | |
|
TMP100 I2C Sensor by CTSchorsch on Tue, 2020-04-21 15:55 |
by CTSchorsch Tue, 2020-04-21 15:55 |
VESC Firmware | ||
|
Print statements - Firmware by vitormhenrique on Sun, 2020-02-23 22:03 |
4 |
by Siverian Sun, 2020-04-19 22:10 |
VESC Firmware | |
|
Firmware Update = Quiet Motor? by worldmaverik on Sun, 2020-04-19 21:45 |
by worldmaverik Sun, 2020-04-19 21:45 |
General discussion | ||
|
Custom VESC4 hardware - disable Regen? by ben5243 on Mon, 2020-04-13 19:48 |
1 |
by hexakopter Sat, 2020-04-18 16:51 |
General discussion | |
|
How to set dead time on BLDC mode? by AllenFF on Wed, 2020-04-15 05:48 |
1 |
by hexakopter Sat, 2020-04-18 16:30 |
VESC Tool | |
|
how I can connect 4 vesc using CAN and how connect vesc to PC via CAN bus? by Chanyoung Jung on Mon, 2020-03-09 08:12 |
1 |
by hexakopter Sat, 2020-04-18 13:12 |
General discussion | |
|
How to update firmware over CAN bus by andrii619 on Wed, 2020-04-15 17:47 |
1 |
by hexakopter Sat, 2020-04-18 12:56 |
General discussion | |
|
No, BLDC is not dead. by Pimousse on Wed, 2019-06-12 17:41 |
5 |
by hexakopter Sat, 2020-04-18 12:30 |
General discussion | |
|
4 vesc motors at once? by i-make-robots on Thu, 2020-04-16 02:17 |
1 |
by hexakopter Sat, 2020-04-18 12:20 |
General discussion |
Pages
