You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
Multiple VESCs on the same battery by Riccio on Wed, 2022-04-20 22:09 |
by Riccio Wed, 2022-04-20 22:09 |
General discussion | ||
|
duty cicle 95% but current not at max by rodrigo.baronio on Mon, 2023-02-06 15:52 |
by rodrigo.baronio Mon, 2023-02-06 15:52 |
VESC Tool | ||
|
"CONTACT Vedder!" by VENTURI on Wed, 2026-10-28 18:26 |
by VENTURI Tue, 2026-11-03 22:28 |
General discussion | ||
|
can't communicate with arduino nrf by m.juan on Mon, 2018-07-02 16:57 |
by m.juan Mon, 2018-07-02 16:57 |
General discussion | ||
|
VESC Replacing Shunt Resistor with Hall Current Sensor? by happy85 on Fri, 2025-07-18 06:21 |
by happy85 Fri, 2025-07-18 11:51 |
General discussion | ||
|
Vesc_tool running error by kwlimm on Sun, 2020-01-19 10:01 |
by kwlimm Sun, 2020-01-19 10:01 |
General discussion | ||
|
VESC_75_300 by jk007 on Fri, 2021-03-19 02:41 |
by jk007 Fri, 2021-03-19 02:41 |
VESC Original Hardware | ||
|
vesc_tool 6 and vesc 4.12 -> motor setup of small outrunner not working by Gawarmel on Thu, 2024-02-29 14:56 |
by Gawarmel Thu, 2024-02-29 14:56 |
VESC Tool | ||
|
Throttle cutout or no response...MK6 + CA3 + Older Stand alone shunt by craigoroszi on Tue, 2025-06-03 05:24 |
by craigoroszi Tue, 2025-06-03 05:24 |
Third Party Hardware | ||
|
Power by kuba12 on Sun, 2021-03-14 20:46 |
by kuba12 Mon, 2021-03-15 15:10 |
General discussion | ||
|
PPM Position over CAN bus? by walleywalker on Thu, 2021-12-02 18:47 |
by walleywalker Thu, 2021-12-02 18:47 |
General discussion | ||
|
problem with encoder readings for proper feedback using arduino by ruthvikchanda on Thu, 2018-12-06 07:05 |
by ruthvikchanda Thu, 2018-12-06 07:05 |
General discussion | ||
|
Closed Loop Control Not Working by Ayden1717 on Sun, 2024-07-14 19:20 |
by Ayden1717 Sun, 2024-07-14 19:20 |
General discussion | ||
|
vesc setup 42V 10A e-bike accu to build in a E-skatboard by olaf2273 on Fri, 2020-04-10 12:33 |
by olaf2273 Mon, 2020-04-27 15:34 |
General discussion | ||
|
Setting RPM over UART by klay2000 on Sat, 2024-06-29 01:27 |
by klay2000 Sat, 2024-06-29 01:28 |
General discussion | ||
|
Bug? by arxera on Sat, 2026-04-04 12:34 |
by arxera Sat, 2026-04-04 12:34 |
VESC Tool | ||
|
Remap Rotary Encoder Input to CAN (or other) by Artemis Skade on Wed, 2020-04-01 20:23 |
by Artemis Skade Wed, 2020-04-01 20:23 |
Feature Requests | ||
|
MakerX-FOC DV6s PWM for 2 BLDC Motors by paulsimpsonii on Tue, 2026-03-03 18:08 |
by paulsimpsonii Tue, 2026-03-03 18:08 |
General discussion | ||
|
Duty vs RPM for smooth start and slow running by Davideo on Tue, 2018-04-24 14:42 |
by Davideo Tue, 2018-04-24 14:42 |
General discussion | ||
|
BLDC zero cross happens too early by Sgw32 on Thu, 2021-05-20 19:10 |
by Sgw32 Thu, 2021-05-20 19:10 |
General discussion |