You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
HW 4.12 USB Device Descriptor Failed-> Red light flashed on start by MTBVASEY on Wed, 2018-04-04 11:06 |
2 |
by MTBVASEY Wed, 2018-04-04 22:24 |
VESC Original Hardware | |
|
Vesc 6 Hardware layout releasing "in the near future" by david_hickox on Wed, 2018-03-07 04:42 |
2 |
by TechAUmNu Wed, 2018-04-04 21:11 |
VESC6 Beta | |
|
Bluetooth connection possible with METR device? by Cuprani on Sun, 2018-04-01 23:00 |
1 |
by Pimousse Wed, 2018-04-04 11:34 |
VESC Tool | |
|
Timeout Brake Current [Fail Save] by Cuprani on Mon, 2018-04-02 00:03 |
2 |
by Cuprani Tue, 2018-04-03 12:28 |
General discussion | |
|
vesc6 help me learn by badger1666 on Sat, 2018-03-31 09:05 |
2 |
by badger1666 Mon, 2018-04-02 20:15 |
General discussion | |
|
VESC hardware interrupt pins by gpzhao on Sun, 2018-04-01 10:47 |
by gpzhao Sun, 2018-04-01 10:50 |
VESC Firmware | ||
|
Hall count drift by xachmo on Mon, 2018-03-26 07:17 |
2 |
by xachmo Wed, 2018-03-28 21:26 |
VESC Original Hardware | |
|
can not start motor with high duty by qdxiatao on Sat, 2018-03-24 03:58 |
by qdxiatao Sat, 2018-03-24 03:58 |
General discussion | ||
|
Can motor parameters be detected with shaft load? by powerlabor001 on Thu, 2018-03-15 13:24 |
4 |
by powerlabor001 Sat, 2018-03-24 03:07 |
General discussion | |
|
Which encoders are supported? by raess on Thu, 2018-03-22 23:38 |
2 |
by raess Fri, 2018-03-23 22:58 |
General discussion | |
|
Motor setup help please by TrevM on Wed, 2017-12-13 17:11 |
2 |
by nickw1881 Wed, 2018-03-21 05:42 |
VESC Tool | |
|
Noise with Hall sensor at high speed by yosoufe on Thu, 2018-03-08 12:34 |
9 |
by yosoufe Tue, 2018-03-20 09:30 |
General discussion | |
|
Low power VESC - any available by wdaehn on Wed, 2018-02-28 18:02 |
9 |
by TechAUmNu Mon, 2018-03-19 11:54 |
Third Party Hardware | |
|
Realtime Tachometer readings over UART by Davideo on Thu, 2017-12-07 00:10 |
1 |
by azobe Mon, 2018-03-19 04:28 |
General discussion | |
|
how to stop regenerative braking option ? by tauhid.ann on Mon, 2018-03-12 18:40 |
5 |
by tauhid.ann Sat, 2018-03-17 21:21 |
General discussion | |
|
UART GND to Battery (-), good idea ? by Pimousse on Sat, 2017-09-23 00:47 |
1 |
by Dillon Sat, 2018-03-17 05:56 |
General discussion | |
|
VESC 6 connection issue by Willoz600 on Wed, 2017-10-04 10:31 |
5 |
by Dillon Sat, 2018-03-17 05:50 |
VESC6 Beta | |
|
Help with a settings for only generator by Mafo on Fri, 2018-03-02 16:59 |
6 |
by Mafo Thu, 2018-03-15 11:15 |
VESC Tool | |
|
Website updates by benjamin on Fri, 2018-02-23 17:45 |
5 |
by benjamin Wed, 2018-03-14 10:46 |
General discussion | |
|
Adding support for three phase shunts... by Roger Wolff on Wed, 2017-11-08 16:03 |
3 |
by georpo Tue, 2018-03-13 14:34 |
VESC Firmware |
Pages
