You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Failure to download VESC Tool by CallumMac on Tue, 2022-01-25 02:38 |
26 |
by Ian Watts Wed, 2022-03-16 12:25 |
VESC Tool | |
|
VESC Blink codes by ligi on Wed, 2022-03-16 12:36 |
1 |
by frank Wed, 2022-03-16 14:57 |
General discussion | |
|
Firmware update for mac needed. by RustyHook on Wed, 2022-03-16 17:50 |
2 |
by RustyHook Wed, 2022-03-16 17:54 |
VESC Firmware | |
|
swap PWM H and PWM L Pins on STM32F4 by Urs_Harry on Tue, 2022-03-15 23:04 |
3 |
by skyline1970 Thu, 2022-03-17 09:58 |
General discussion | |
|
Increasing phase amps beyond 300a on 100-250 by reubarb.scons on Tue, 2022-03-15 07:30 |
4 |
by reubarb.scons Thu, 2022-03-17 22:28 |
VESC Original Hardware | |
|
Need IRF7759 by marcel7162 on Fri, 2022-03-18 22:29 |
by marcel7162 Fri, 2022-03-18 22:29 |
Third Party Hardware | ||
|
RC Car BLDC - Hall Effect Timing Angle Calculator by mendez on Mon, 2022-03-14 19:20 |
5 |
by sp3swj Sat, 2022-03-19 11:36 |
General discussion | |
|
VESC6 Issues: Battery current inaccurate, positive ramp time, motor current max. by ESCam on Thu, 2019-03-21 22:50 |
4 |
by sp3swj Sat, 2022-03-19 15:07 |
VESC Original Hardware | |
|
Cant connect to Flipsky 75100 by Ed222 on Sun, 2022-03-20 00:31 |
3 |
by Ed222 Sun, 2022-03-20 19:01 |
General discussion | |
|
ADC INPUT with 4.10 HW running with 5.02 FW by mouadh on Tue, 2022-03-22 15:32 |
by mouadh Tue, 2022-03-22 17:38 |
General discussion | ||
|
ESP32 VESC controller by Ortsac on Fri, 2022-01-21 18:50 |
2 |
by Gatze Wed, 2022-03-23 10:50 |
General discussion | |
|
Generic dual drive Ebay controller speed by stefann on Wed, 2022-03-23 21:14 |
by stefann Wed, 2022-03-23 21:14 |
Third Party Hardware | ||
|
VESC-Tool Bugs by Danny Bokma on Sun, 2017-06-04 01:44 |
13 |
by sevenfloorsdown Wed, 2022-03-23 22:45 |
VESC6 Beta | |
|
FS75100 by Filip Kinl on Sun, 2022-02-27 16:42 |
2 |
by Oded Mazor Thu, 2022-03-24 12:02 |
Third Party Hardware | |
|
Need Help with HI200-C from Maker X by Moritz@liebler.net on Tue, 2021-01-12 14:44 |
4 |
by Oded Mazor Thu, 2022-03-24 12:05 |
Third Party Hardware | |
|
IMU 9250 and 6050 not working on new vesc 4.12 and 4.20 by trung_qly on Sun, 2021-09-05 16:11 |
2 |
by skyline1970 Thu, 2022-03-24 20:57 |
General discussion | |
|
Heavy applications ? by nojjan on Mon, 2022-03-21 20:46 |
1 |
by skyline1970 Thu, 2022-03-24 21:26 |
General discussion | |
|
Sending Negative Values to VESC over CAN bus by olivierabristol on Fri, 2022-03-25 09:11 |
by olivierabristol Fri, 2022-03-25 09:13 |
VESC Firmware | ||
|
5000 rpm BLDC, 1600 rpm FOC by scubersteve on Mon, 2022-03-21 03:10 |
1 |
by skyline1970 Fri, 2022-03-25 18:45 |
VESC Tool | |
|
2nd Maytech 75_300 burned by Flyingtux on Wed, 2022-03-16 22:15 |
1 |
by skyline1970 Fri, 2022-03-25 19:00 |
General discussion |
Pages
