You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
VESC Remote - Input Deadband setting causing severe input delay as well as changing deadband by agraham on Wed, 2022-07-13 07:41 |
by agraham Wed, 2022-07-13 07:42 |
VESC Firmware | ||
|
Cruise control by palaga on Tue, 2025-05-20 09:20 |
by palaga Tue, 2025-05-20 09:20 |
General discussion | ||
|
The engine stopped spinning after updating firmware by brian adilman on Wed, 2022-01-26 17:40 |
by brian adilman Wed, 2022-01-26 19:15 |
VESC Firmware | ||
|
How to activate e-brake on e-scooter with the throttle by Donatas Sukelis on Sat, 2019-04-27 10:09 |
by Donatas Sukelis Sat, 2019-04-27 10:09 |
VESC Tool | ||
|
Flipsky losing its settings by jrowe on Tue, 2019-04-16 00:34 |
by jrowe Tue, 2019-04-16 00:34 |
Third Party Hardware | ||
|
Dutycycle set using uart problem by Raja Sharma on Tue, 2020-07-21 21:38 |
by Raja Sharma Tue, 2020-07-21 21:38 |
VESC Firmware | ||
|
Controlling (HB) Braking from Arduino by Bruce on Sat, 2021-02-27 00:23 |
by Bruce Sat, 2021-02-27 00:23 |
General discussion | ||
|
Programming VESC through CANbus adapter by Filcas on Sat, 2020-03-28 11:43 |
by Filcas Sat, 2020-03-28 11:43 |
VESC Tool | ||
|
Current measurement VESC Tool 1.16 by mdbb on Thu, 2020-03-19 17:16 |
by mdbb Thu, 2020-03-19 17:16 |
VESC Tool | ||
|
Sensored mode studering by dtmpro621 on Thu, 2023-03-02 04:40 |
by dtmpro621 Thu, 2023-03-02 05:25 |
General discussion | ||
|
Center-aligned PWM and ADC sampling. Custom firmware by ecodev on Wed, 2020-10-07 10:42 |
by ecodev Wed, 2020-10-07 10:42 |
VESC Firmware | ||
|
Power Switch by flyingbrike on Wed, 2021-09-08 13:47 |
by flyingbrike Wed, 2021-09-08 13:47 |
General discussion | ||
|
Got the judders by Phill Dixon on Sun, 2018-05-13 17:45 |
by Phill Dixon Sun, 2018-05-13 17:45 |
General discussion | ||
|
FOC Motor Detection Values Incorrect, PID Tuning Advice? by bmwman91 on Mon, 2020-07-06 03:09 |
by bmwman91 Mon, 2020-07-06 03:21 |
VESC Tool | ||
|
75300 r2 v5.3 by Oscarmanassan on Tue, 2022-09-27 14:23 |
by Oscarmanassan Tue, 2022-09-27 14:23 |
VESC Firmware | ||
|
Using vesc between many motors by EliProtiva on Tue, 2021-02-16 05:32 |
by EliProtiva Tue, 2021-02-16 05:32 |
General discussion | ||
|
no effect on set erpm/speed limit by xenon321 on Sat, 2021-04-24 20:43 |
by xenon321 Sun, 2021-04-25 16:53 |
VESC Tool | ||
|
Fsesc 4.20 plus aiuto by sandrino on Sun, 2023-01-22 20:50 |
by sandrino Mon, 2023-01-23 21:13 |
Third Party Hardware | ||
|
VESC 75/300 singnal connectors by Mikko Valtonen on Tue, 2020-05-19 21:43 |
by Mikko Valtonen Tue, 2020-05-19 21:43 |
VESC Original Hardware | ||
|
Wheel speed over CANBUS by paule on Tue, 2020-12-29 13:04 |
by paule Tue, 2020-12-29 13:04 |
General discussion |
Pages
