You are here
Active forum topics
Primary tabs
| Topic |
Replies |
Last post | Forum | |
|---|---|---|---|---|
|
foc detection params by stefann on Mon, 2020-04-13 00:07 |
by stefann Mon, 2020-04-13 00:28 |
VESC Tool | ||
|
Tuning process? by wingborne on Tue, 2020-09-29 00:09 |
by wingborne Tue, 2020-09-29 21:39 |
General discussion | ||
|
Is there a way to deactivate roll to start function FW 5.02 by Philo on Sun, 2021-04-11 13:55 |
by Philo Sun, 2021-04-11 13:58 |
Third Party Hardware | ||
|
100_250_mkiii official release by hugros on Mon, 2023-08-07 15:40 |
by hugros Mon, 2023-08-07 15:40 |
VESC Firmware | ||
|
id/iq Table input by red.blaylock on Fri, 2020-05-22 09:20 |
by red.blaylock Fri, 2020-05-22 12:11 |
Feature Requests | ||
|
Apply current to brake at low speed by argon338 on Wed, 2022-08-17 08:36 |
by argon338 Thu, 2022-08-25 17:08 |
Feature Requests | ||
|
error message binding loop detected for property ! wtf by georg65 on Sat, 2024-09-28 08:49 |
by georg65 Tue, 2024-10-01 03:04 |
General discussion | ||
|
9 by RoopeKuisma on Sun, 2020-05-10 21:58 |
by RoopeKuisma Sun, 2020-05-10 21:58 |
General discussion | ||
|
one motor spinning faster than the other? by jon218white on Mon, 2020-12-14 22:57 |
by jon218white Mon, 2020-12-14 22:57 |
VESC Tool | ||
|
Reverse Button Status over UART? by Rich235 on Sat, 2024-09-07 10:34 |
by Rich235 Sat, 2024-09-07 10:34 |
General discussion | ||
|
Problem after flash fw 3.38 detection faild dont spin by kataklysm_9090 on Tue, 2018-06-19 22:48 |
by kataklysm_9090 Tue, 2018-06-19 22:48 |
VESC Firmware | ||
|
External Bluetooth and IMU on CAN-connected VESCs by frankus on Sat, 2022-03-26 19:58 |
by frankus Sat, 2022-03-26 19:58 |
General discussion | ||
|
PWM length not correctly measured by ufechner on Tue, 2018-06-05 11:45 |
by ufechner Tue, 2018-06-05 11:45 |
VESC Firmware | ||
|
How to set up RF receiver for PPM or UART input? by adamdorr on Tue, 2020-01-07 16:23 |
by adamdorr Tue, 2020-01-07 16:23 |
General discussion | ||
|
Backup file by Done on Tue, 2020-07-28 12:08 |
by Done Tue, 2020-07-28 12:08 |
VESC Tool | ||
|
Reset parameters by nidhirao on Mon, 2019-12-23 10:57 |
by nidhirao Mon, 2019-12-23 10:57 |
VESC Tool | ||
|
Making master and slave motors communicate both ways by Sis7 on Tue, 2020-07-21 05:58 |
by Sis7 Tue, 2020-07-21 05:58 |
General discussion | ||
|
Custom GUI by FatsoBatso on Thu, 2021-02-25 16:10 |
by FatsoBatso Thu, 2021-02-25 16:10 |
VESC Tool | ||
|
Change the direction of motor when using PPM and "Current no reverse with brake"? by Kokonenen on Mon, 2023-04-24 13:41 |
by Kokonenen Mon, 2023-04-24 13:41 |
VESC Firmware | ||
|
Tool for OSX MAC by oger on Wed, 2020-03-25 17:21 |
by oger Wed, 2020-03-25 17:21 |
VESC Tool |
Pages
