You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
3rd harmonic injection or SVPWM/ Midpoint Clamp for FOC by ufechner » Sat, 2018-04-21 06:05 |
3 |
by arvidb Tue, 2018-05-08 16:35 |
|
|
Cannot upgrade firmware by greensightag.com » Fri, 2018-04-27 02:32 |
0 |
by greensightag.com Fri, 2018-04-27 02:34 |
|
|
Firmware 3.37 too old, unable to Connect VESC_Tool by Nico Isn » Wed, 2018-04-18 11:17 |
2 |
by Nico Isn Fri, 2018-04-20 16:31 |
|
|
Problems with writing Firmware to the processor by Goex » Wed, 2018-03-28 09:11 |
2 |
by Idoff Tue, 2018-04-17 11:04 |
|
|
VESC hardware interrupt pins by gpzhao » Sun, 2018-04-01 10:47 |
0 |
by gpzhao Sun, 2018-04-01 10:50 |
|
|
Adding support for three phase shunts... by Roger Wolff » Wed, 2017-11-08 16:03 |
3 |
by georpo Tue, 2018-03-13 14:34 |
|
|
How to modify default firmware? by lorenzo211 » Sun, 2018-03-11 19:15 |
2 |
by yosoufe Mon, 2018-03-12 14:17 |
|
|
Twisted pair for Can Bus link cable? by Kenny-san650 » Tue, 2018-02-13 08:35 |
2 |
by Kenny-san650 Mon, 2018-02-19 09:15 |
|
|
Will voltage offset on phase cause tracking to get wrong position? by TechAUmNu » Wed, 2018-01-17 18:14 |
1 |
by TechAUmNu Wed, 2018-01-17 21:42 |
|
|
Calculation of Current and Voltage by Christian » Tue, 2017-12-12 10:12 |
5 |
by Roger Wolff Sun, 2018-01-07 15:41 |
|
|
Bug: Tachometer does not change when handbrake is turned on by wdaehn » Mon, 2017-12-25 10:12 |
0 |
by wdaehn Mon, 2017-12-25 10:12 |
|
|
VESC 6.0 Hardware Shows Up As HW 410 in VESC-Tool by FWachter » Thu, 2017-12-21 20:51 |
1 |
by wdaehn Fri, 2017-12-22 08:22 |
|
|
Flux linkage observer @ low speed by soltesz » Sun, 2017-12-17 16:33 |
9 |
by benjamin Thu, 2017-12-21 10:17 |
|
|
[Contributing][FOC] injected ADC and code clarity by Guillaume227 » Fri, 2017-12-15 18:00 |
1 |
by Roger Wolff Sat, 2017-12-16 13:21 |
|
|
Upgraded from 2.18 to 3.33 - Lost Telemetry by ervinelin » Thu, 2017-11-23 09:09 |
1 |
by Pedrodemio Thu, 2017-11-23 17:03 |
|
|
temp motor by emmaanuel » Wed, 2017-09-13 01:27 |
12 |
by Roger Wolff Wed, 2017-11-08 16:23 |
|
|
Compiling Error Windows 10 by Christian » Mon, 2017-10-16 11:58 |
2 |
by Svenska Svenson Sun, 2017-10-29 19:25 |
|
|
set current with custom app by sirAnton » Thu, 2017-10-12 12:42 |
2 |
by benjamin Thu, 2017-10-19 21:10 |
|
|
speed control anti windup improvement by RSR » Thu, 2017-09-07 10:02 |
1 |
by benjamin Thu, 2017-10-19 20:57 |
|
|
Firmware 3.29 hardware 4.12 , 0.5mOhm shunts by brushlessdevil » Sun, 2017-10-15 19:28 |
1 |
by benjamin Thu, 2017-10-19 15:15 |
|
|
Help with Focbox firmware / bootloader upgrade [VESC TOOL] by Enigmacpl03 » Thu, 2017-10-05 17:21 |
0 |
by Enigmacpl03 Thu, 2017-10-05 17:21 |
|
|
PID Speed Control code....for NRF by Dimitri » Tue, 2017-10-03 07:16 |
0 |
by Dimitri Tue, 2017-10-03 07:18 |
|
|
VESC4.12 new fmw issue by jsy070913 » Thu, 2017-09-07 04:26 |
10 |
by Silverline Sat, 2017-09-30 08:42 |
|
|
Maybe a typo in the code by Ackmaniac » Wed, 2017-09-06 12:34 |
3 |
by Dimitri Tue, 2017-09-26 08:46 |
|
|
Bypass NRF Pairing by Dimitri » Wed, 2017-09-20 09:35 |
1 |
by benjamin Fri, 2017-09-22 13:57 |
Log in to post new content in the forum.
