You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
VESC PID by nidhirao » Tue, 2019-12-17 13:56 |
0 |
by nidhirao Tue, 2019-12-17 13:56 |
|
|
Spin the motor and stop at a set tachometer index by jchillerup » Tue, 2019-12-10 12:29 |
1 |
by frank Wed, 2019-12-11 14:51 |
|
|
FEATURE REQUEST - ADC Mapping selection by Pimousse » Thu, 2018-09-13 09:44 |
2 |
by hackish Sun, 2019-12-08 03:53 |
|
|
Firmware failure? Updating BLE trough SWD fails by dk-odense » Wed, 2019-11-13 09:07 |
3 |
by frank Thu, 2019-12-05 11:16 |
|
|
VESC for Multirotor / Betaflight flight controller SBUS input by Autek-Xracing » Sun, 2017-11-26 01:39 |
5 |
by jordanlow Sun, 2019-11-24 13:30 |
|
|
Current sense SNA/SPA swapped. Where to adjust the code? by shaman » Fri, 2019-11-08 14:51 |
1 |
by Eric Fri, 2019-11-15 11:49 |
|
|
download older version of Vesc tool android app by jakebarnhill1 » Sun, 2019-04-28 12:16 |
8 |
by mustafa Sun, 2019-11-10 21:04 |
|
|
200kHz PWM by c10yas » Sun, 2019-09-22 17:06 |
2 |
by Eric Thu, 2019-11-07 18:09 |
|
|
paltatech v0.2 HW not supported in latest firmware? by samuelis01 » Sun, 2019-10-27 22:52 |
0 |
by samuelis01 Sun, 2019-10-27 22:52 |
|
|
Unable to flash firmware to VESC using OpenOCD by Bayne » Fri, 2019-10-25 02:34 |
0 |
by Bayne Fri, 2019-10-25 02:35 |
|
|
New Control Algorithm for asynchronous machines by ajpina » Sun, 2019-05-19 22:13 |
4 |
by Henque19 Wed, 2019-10-16 23:29 |
|
|
physical meaning of current KI and current KP coefficients by ExiD » Tue, 2019-10-15 16:38 |
0 |
by ExiD Tue, 2019-10-15 16:38 |
|
|
mcpwm_foc and mcpwm tutorial by nami1216 » Tue, 2019-10-15 07:12 |
0 |
by nami1216 Tue, 2019-10-15 07:12 |
|
|
USB connection problem by Ironman223 » Sat, 2019-10-12 13:53 |
0 |
by Ironman223 Sat, 2019-10-12 13:53 |
|
|
Limiting switching frequency of the SPWM for big IGBT´s by javivi » Wed, 2019-10-09 13:32 |
2 |
by javivi Thu, 2019-10-10 09:41 |
|
|
Measure resistance with IGBTs by mtzm » Wed, 2018-04-04 14:46 |
4 |
by jaredreese Thu, 2019-10-03 11:41 |
|
|
Generator app by arvidb » Sat, 2018-09-22 01:03 |
3 |
by stiganielsen Fri, 2019-09-20 14:29 |
|
|
PID - Position Angle Division by robo_studienarbeit » Tue, 2018-12-04 18:46 |
1 |
by Nellieorton Fri, 2019-09-20 06:49 |
|
|
Cant seem to update my firmware on my VECS. by mackattack » Tue, 2019-07-30 16:23 |
7 |
by mikej_w Thu, 2019-09-19 00:55 |
|
|
Problems getting Cruise control to run properly with the new wand - dual VESC6 by MaddiQ » Mon, 2019-09-16 19:36 |
0 |
by MaddiQ Mon, 2019-09-16 19:36 |
|
|
Problems with flashing firmware to FLIPSKY ESC by xx11xx » Wed, 2019-08-14 18:10 |
1 |
by kinzma Tue, 2019-08-20 07:56 |
|
|
Add serial port by CTSchorsch » Wed, 2019-08-14 15:30 |
0 |
by CTSchorsch Wed, 2019-08-14 15:30 |
|
|
Problem report: VESC keeps running at full reverse throttle after PPM input returns to mid-stick by chunkulator » Sun, 2019-08-11 00:34 |
0 |
by chunkulator Sun, 2019-08-11 00:34 |
|
|
what do you guys think about this "curr_samp_volt "? by jem » Thu, 2019-08-08 14:45 |
0 |
by jem Thu, 2019-08-08 14:45 |
|
|
VESC4 phase shunt by Rico » Tue, 2019-05-21 16:09 |
3 |
by svs Thu, 2019-08-08 08:41 |
Log in to post new content in the forum.
