You are here
VESC Firmware
Log in to post new content in the forum.
| Topic / Topic starter | Replies |
Last post |
|
|---|---|---|---|
|
How Update firmware vesc 6.41 with broken micro USB fw 3.40? by adrian210188 » Thu, 2020-03-12 01:18 |
1 |
by Pimousse Sat, 2020-03-21 13:01 |
|
|
Control Algorithm for Sensorless FOC control by vimi94 » Wed, 2019-11-06 18:56 |
6 |
by kaanozgen Tue, 2020-03-17 10:34 |
|
|
"Porting" VESC FW to physically smaller device? by Jackl » Fri, 2020-03-13 14:04 |
2 |
by Jackl Mon, 2020-03-16 14:52 |
|
|
re-scaling CAN setDUTY CYCLE to -1 to 1 instead of 0 to 1 by a.dahhak » Fri, 2020-03-06 11:09 |
1 |
by a.dahhak Mon, 2020-03-09 10:38 |
|
|
Enabling WS2811 not working by vitormhenrique » Thu, 2020-03-05 03:42 |
0 |
by vitormhenrique Thu, 2020-03-05 03:42 |
|
|
Duty cycle take 95% when motor released by Rarikao » Mon, 2019-12-23 08:57 |
2 |
by agnesnorris Sat, 2020-02-29 03:48 |
|
|
Compiling corrupted firmwares... by vitormhenrique » Sun, 2020-02-23 22:38 |
6 |
by district9prawn Tue, 2020-02-25 23:39 |
|
|
AHRS yaw drifting by henry10210 » Sun, 2020-02-09 01:13 |
0 |
by henry10210 Sun, 2020-02-09 01:13 |
|
|
MK3 branch in bldc repo? by henry10210 » Tue, 2019-12-31 23:49 |
1 |
by Teslafly Thu, 2020-02-06 21:22 |
|
|
Hardware limits 3.66 by rumpsvett » Thu, 2020-01-16 19:50 |
0 |
by rumpsvett Thu, 2020-01-16 22:31 |
|
|
noob question - how to I update FW to 3.66? by brently » Thu, 2020-01-16 02:22 |
0 |
by brently Thu, 2020-01-16 02:22 |
|
|
Dual motor setup over CAN with UART by Pawel » Sun, 2018-06-17 11:50 |
5 |
by alex63610 Fri, 2019-12-27 14:27 |
|
|
No reverse after FW update from 3.62 to 3.63 by Stupidspencer » Sun, 2019-12-15 20:34 |
4 |
by Stupidspencer Sun, 2019-12-22 21:57 |
|
|
3.64 can_scan breaks with ppm enabled. by fessyfoo » Fri, 2019-12-20 20:40 |
1 |
by fessyfoo Sun, 2019-12-22 03:44 |
|
|
VESC PID by nidhirao » Tue, 2019-12-17 13:56 |
0 |
by nidhirao Tue, 2019-12-17 13:56 |
|
|
Unity FW updating bricked my 4.12 HW by yuvikal » Thu, 2019-12-12 22:16 |
3 |
by frank Sat, 2019-12-14 20:03 |
|
|
Spin the motor and stop at a set tachometer index by jchillerup » Tue, 2019-12-10 12:29 |
1 |
by frank Wed, 2019-12-11 14:51 |
|
|
FEATURE REQUEST - ADC Mapping selection by Pimousse » Thu, 2018-09-13 09:44 |
2 |
by hackish Sun, 2019-12-08 03:53 |
|
|
Firmware failure? Updating BLE trough SWD fails by dk-odense » Wed, 2019-11-13 09:07 |
3 |
by frank Thu, 2019-12-05 11:16 |
|
|
VESC for Multirotor / Betaflight flight controller SBUS input by Autek-Xracing » Sun, 2017-11-26 01:39 |
5 |
by jordanlow Sun, 2019-11-24 13:30 |
|
|
Current sense SNA/SPA swapped. Where to adjust the code? by shaman » Fri, 2019-11-08 14:51 |
1 |
by Eric Fri, 2019-11-15 11:49 |
|
|
download older version of Vesc tool android app by jakebarnhill1 » Sun, 2019-04-28 12:16 |
8 |
by mustafa Sun, 2019-11-10 21:04 |
|
|
200kHz PWM by c10yas » Sun, 2019-09-22 17:06 |
2 |
by Eric Thu, 2019-11-07 18:09 |
|
|
paltatech v0.2 HW not supported in latest firmware? by samuelis01 » Sun, 2019-10-27 22:52 |
0 |
by samuelis01 Sun, 2019-10-27 22:52 |
|
|
Unable to flash firmware to VESC using OpenOCD by Bayne » Fri, 2019-10-25 02:34 |
0 |
by Bayne Fri, 2019-10-25 02:35 |
Log in to post new content in the forum.
