You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Cannot connect win10 tried everything I have read by meziked on Wed, 2025-07-02 00:45 |
2 |
by meziked Wed, 2025-07-02 16:21 |
VESC Tool | |
|
Hoverboard Motor Setup by CadillacF1 on Sat, 2020-07-11 05:26 |
3 |
by meziked Wed, 2025-07-02 16:13 |
VESC Tool | |
|
VESC 75/300 repair by mah on Tue, 2025-07-01 16:16 |
by mah Tue, 2025-07-01 16:16 |
VESC Original Hardware | ||
|
Connecting VESC (FSESC75200) to Flight Controller (Matek H743) for Rover — Setup and Recommendations by ispor4en on Fri, 2025-06-27 21:36 |
by ispor4en Fri, 2025-06-27 21:36 |
Projects incorporating VESC technology | ||
|
Repairing by lamak on Thu, 2025-06-26 07:08 |
2 |
by ispor4en Fri, 2025-06-27 21:15 |
General discussion | |
|
eRPM limited to 40600 or so on 6.6 by Dan Slanker on Fri, 2021-04-16 01:22 |
6 |
by electricfox Wed, 2025-06-18 10:11 |
General discussion | |
|
bootloader and firmware update for vesc 4.12 by enjoae on Thu, 2025-05-22 19:17 |
2 |
by tobydraper Sun, 2025-06-15 22:22 |
VESC Firmware | |
|
Switch between pre-defined profiles over UART by PutridFox on Sun, 2025-06-15 13:11 |
by PutridFox Sun, 2025-06-15 13:11 |
General discussion | ||
|
Looking for VESC Tuning Help will pay $ by jordan73s on Sun, 2025-05-04 02:23 |
2 |
by colmor Thu, 2025-06-12 21:35 |
General discussion | |
|
Different Tiers for VESC Tool by Reki on Thu, 2025-06-12 00:32 |
1 |
by Reki Thu, 2025-06-12 00:33 |
VESC Tool | |
|
Innotrace X1 motor controller for Bafang m620 UART with VESC firmware by TPEHAK on Tue, 2025-06-10 22:00 |
by TPEHAK Tue, 2025-06-10 22:03 |
VESC Firmware | ||
|
IMU 9250 and 6050 not working on new vesc 4.12 and 4.20 by trung_qly on Sun, 2021-09-05 16:11 |
3 |
by spatsirk Mon, 2025-06-09 18:55 |
General discussion | |
|
Using the parameter editor by dqt boi on Thu, 2019-10-24 23:31 |
1 |
by Anuj Sat, 2025-06-07 16:23 |
General discussion | |
|
Flipsky 75100 V2 with Maxon 386675 by GoFast99 on Thu, 2025-06-05 20:54 |
by GoFast99 Thu, 2025-06-05 20:54 |
Third Party Hardware | ||
|
base on VESC6_MkVI by gavin on Wed, 2025-06-04 15:48 |
by gavin Wed, 2025-06-04 15:48 |
General discussion | ||
|
vesc tool by gavin on Wed, 2025-06-04 15:30 |
1 |
by gavin Wed, 2025-06-04 15:31 |
General discussion | |
|
Throttle cutout or no response...MK6 + CA3 + Older Stand alone shunt by craigoroszi on Tue, 2025-06-03 05:24 |
by craigoroszi Tue, 2025-06-03 05:24 |
Third Party Hardware | ||
|
Flipsky FSESC75100 & FSESC75200 Phase Filtering by j.konrad on Sat, 2022-04-02 00:17 |
13 |
by Fr33man Mon, 2025-06-02 17:33 |
Third Party Hardware | |
|
Dev Tools (Scripting) by curt on Mon, 2022-08-22 15:16 |
1 |
by nico01 Thu, 2025-05-29 17:04 |
VESC Tool | |
|
Flipsky and Trampa getting two very different detected resistances on same motor! by colmor on Wed, 2025-05-28 22:52 |
by colmor Wed, 2025-05-28 22:52 |
General discussion |
Pages
