You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
Flipsky Dual 75100 forward, brake, and reverse by Shockwave333 on Wed, 2023-02-15 02:58 |
1 |
by voodoobrew Sat, 2025-12-20 23:40 |
Third Party Hardware | |
|
open gl issue by TONY61 on Fri, 2025-12-19 17:00 |
by TONY61 Fri, 2025-12-19 17:00 |
VESC Tool | ||
|
Not able to drive output current by tecmarek on Tue, 2024-12-10 10:49 |
2 |
by Than Thu, 2025-12-18 03:23 |
Third Party Hardware | |
|
VESC 6 MK5 Dectection Failed DRV fault by Than on Thu, 2025-12-18 03:02 |
by Than Thu, 2025-12-18 03:02 |
Third Party Hardware | ||
|
FSESC 75100 Pro V2 W/ ALUMINUM by drstein99 on Tue, 2025-08-26 23:02 |
2 |
by CRTZ Wed, 2025-12-17 14:16 |
VESC Firmware | |
|
How I disconnect CAN communation between two ESCs in dual channel ESC by Adesh Kute on Tue, 2025-12-16 08:10 |
by Adesh Kute Tue, 2025-12-16 08:10 |
VESC Tool | ||
|
Modifications Needed for Custom Dual Motor ESC for 3S Operation by NK-108 on Mon, 2025-12-15 18:27 |
by NK-108 Mon, 2025-12-15 18:27 |
VESC Firmware | ||
|
Issue connecting to Flipsky VESC with mobile app (Firmware 6.0.6) by Gabifat on Mon, 2025-12-15 08:35 |
by Gabifat Mon, 2025-12-15 08:35 |
General discussion | ||
|
Need help: encoder shows 9.6 rotations per 1 motor rotation (9.6:1 gearbox) by Alico on Thu, 2025-12-11 14:41 |
by Alico Thu, 2025-12-11 14:41 |
VESC Tool | ||
|
tuning low kv high pole sensorless outrunner by cdlapoin on Tue, 2025-05-20 22:14 |
3 |
by flagoworld Wed, 2025-12-10 19:29 |
General discussion | |
|
Motor "sticks" and stops spinning by flagoworld on Fri, 2025-12-05 19:03 |
by flagoworld Fri, 2025-12-05 19:03 |
General discussion | ||
|
Blown FETs VESC100/250 MKIII by Joe90 on Sat, 2025-11-29 17:47 |
by Joe90 Sun, 2025-11-30 17:28 |
Projects incorporating VESC technology | ||
|
Running motors under 900ERPM in speed control by Chieflouis01 on Thu, 2025-11-27 21:32 |
2 |
by Chieflouis01 Thu, 2025-11-27 21:33 |
General discussion | |
|
Flipsky 75100 V2 ADC Filtering? by lorentz343 on Thu, 2025-11-27 14:57 |
1 |
by lorentz343 Thu, 2025-11-27 20:58 |
Third Party Hardware | |
|
Uart and Usb tx not working by Camolas on Wed, 2025-11-26 08:08 |
by Camolas Wed, 2025-11-26 08:08 |
Third Party Hardware | ||
|
VESC hardware without using a DRV chip by kyletseng on Fri, 2025-11-21 09:07 |
by kyletseng Fri, 2025-11-21 09:07 |
Third Party Hardware | ||
|
Speed mode with zero speed hold by mpalamar on Thu, 2025-10-09 16:15 |
3 |
by Matevz Wed, 2025-11-19 10:54 |
Feature Requests | |
|
position hold below specific duty cycle by lacondro on Wed, 2022-04-27 04:41 |
3 |
by Matevz Tue, 2025-11-18 14:17 |
VESC Firmware | |
|
VESC Tool IMU Problem by 13.meshhi on Sun, 2025-11-16 23:40 |
by 13.meshhi Sun, 2025-11-16 23:40 |
VESC Tool | ||
|
Motor stopped and I had to run Setup Motors FOC wizard to get it going again by JasonBear on Fri, 2025-11-14 13:24 |
2 |
by JasonBear Sun, 2025-11-16 20:41 |
General discussion |
Pages
