You are here
Active forum topics
Primary tabs
| Topic | Replies |
Last post |
Forum | |
|---|---|---|---|---|
|
DUAL VESC FOR BIDIRECTIONAL ROTATION by Khaliduzzaman Mredul on Fri, 2023-05-05 06:46 |
by Khaliduzzaman Mredul Fri, 2023-05-05 11:00 |
General discussion | ||
|
[SOLVED] PWM speed control at low RPM by comes04 on Sun, 2023-04-16 13:30 |
1 |
by comes04 Wed, 2023-05-03 20:44 |
General discussion | |
|
[SOLVED, was a mistake] Set ERPM command: issue with the speed controller with higher speed values that is possible with bat vol by yes_wecangogreen on Wed, 2023-04-12 00:51 |
1 |
by yes_wecangogreen Sat, 2023-04-29 09:24 |
General discussion | |
|
C Type USB and Power Delivery 3.1 by Rarikao on Fri, 2023-04-21 08:51 |
4 |
by vadicus Fri, 2023-04-28 05:30 |
Feature Requests | |
|
Ground Housing VESC by T18m26 on Mon, 2023-04-17 16:25 |
2 |
by T18m26 Thu, 2023-04-27 08:28 |
VESC Original Hardware | |
|
Driving Synchronous reluctance motor using VESC by mmandar90 on Fri, 2023-04-21 14:34 |
2 |
by Ganzey Thu, 2023-04-27 00:17 |
VESC Firmware | |
|
RT Data Logging by adas29 on Wed, 2023-04-26 22:59 |
by adas29 Wed, 2023-04-26 22:59 |
VESC Tool | ||
|
"CAN bus support is not enabled in this build of VESC Tool" by hdfghdfgh on Wed, 2023-04-26 16:13 |
by hdfghdfgh Wed, 2023-04-26 16:13 |
VESC Tool | ||
|
Bench Testing by usaevo7 on Tue, 2023-04-25 16:50 |
by usaevo7 Tue, 2023-04-25 16:50 |
General discussion | ||
|
Accidentally Bricked MakerX Go-Foc D60 by masong on Mon, 2023-04-24 07:41 |
by masong Tue, 2023-04-25 03:20 |
VESC Firmware | ||
|
EBike Bafang M500 mide drive motor: VESC + DIY ESP32 board running Pyhton firmware by yes_wecangogreen on Wed, 2023-04-12 00:43 |
by yes_wecangogreen Tue, 2023-04-25 02:04 |
Projects incorporating VESC technology | ||
|
despin platform by wjpremerlani on Fri, 2023-03-31 19:54 |
by wjpremerlani Mon, 2023-04-24 15:38 |
Projects incorporating VESC technology | ||
|
Maytech 100a ESC by NOldfield on Sat, 2023-04-22 08:51 |
by NOldfield Mon, 2023-04-24 15:32 |
Third Party Hardware | ||
|
Change the direction of motor when using PPM and "Current no reverse with brake"? by Kokonenen on Mon, 2023-04-24 13:41 |
by Kokonenen Mon, 2023-04-24 13:41 |
VESC Firmware | ||
|
VESC TOOL Mobile over OTG by xvatriusx on Sat, 2022-08-13 04:25 |
1 |
by besenyeim Mon, 2023-04-24 12:26 |
Feature Requests | |
|
Vesc for 5000kW QS 205 Hub Motor ebike by Amiran on Fri, 2019-09-27 15:52 |
10 |
by vadicus Sun, 2023-04-23 01:23 |
General discussion | |
|
Can't spin both motors over CAN-bus by Kokonenen on Wed, 2023-04-19 11:19 |
3 |
by Kokonenen Fri, 2023-04-21 09:18 |
VESC Tool | |
|
Trapezoidal Trajectory/Position Control by wewa on Sun, 2018-09-23 11:33 |
4 |
by ncbanse Thu, 2023-04-20 21:26 |
Feature Requests | |
|
Parameters for efoil by vladek on Thu, 2023-04-20 12:54 |
by vladek Thu, 2023-04-20 12:54 |
VESC Tool | ||
|
Can't get Dual drive/CAN bus working by Xadiant on Sun, 2019-09-22 20:49 |
11 |
by Kokonenen Wed, 2023-04-19 11:10 |
VESC Tool |
Pages
